- 您現在的位置：買賣IC網 > PDF目錄299499 > MLX90609EEA-R2 SPECIALTY ANALOG CIRCUIT, CQCC32 PDF資料下載
參數資料
| 型號： | MLX90609EEA-R2 |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, CQCC32 |
| 封裝： | CERAMIC, LCC-32 |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 550K |
| 代理商： | MLX90609EEA-R2 |
MLX90609
Angular Rate Sensor (Standard version)
390109060901
Page 14 of 22
Data Sheet
Rev 010
November/08
5.3.2 Reading the Digital Angular Rate or Temperature (suggested procedure)
There is a recommended sequence below to obtain digital data from the ADC.
Notes:
- The bit with leftmost position should be shifted first.
- Below “x” means any value: “0” or “1”.
Step 1 (put ADC to the active mode if it wasn’t)
Use SPI to send ADCC instruction (MOSI): 1 0 0 1 x 1 0 0 x x x x x x x x x x x x x x x x
And check 15th bit of the answer (MISO):
0 x x x x x x x x x x x x x x x
If 15
th
bit is zero, the instruction is accepted.
Before to go to the Step 2 provide a delay > 115 s or wait till the EOC bit is set.
Step 2 (conversion start)
Use SPI to send ADCC instruction(MOSI):1 0 0 1 CHAN 1 0 0 x x x x x x x x x x x x x x x x
And check 15th bit of the answer (MISO):
0 x x x x x x x x x x x x x x x
If 15
th
bit is zero, the instruction is accepted.
CHAN bit specifies the input source of the ADC.
CHAN=0: The angular rate signal.
CHAN=1: The temperature sensor signal.
Go to the Step 3.
Step 3 (polling and result obtaining)
Use SPI to send ADCR instruction and check 15
th
and 13
th
bits of the answer:
1
0
x
0
x EOC x
AD10 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 0
If 15
th
bit is zero, the instruction is accepted.
If
13
th
bit
(EOC)
is zero,
the
conversion
is
still
in
progress and
the
result
of
the
conversion (bits AD10…AD0) is not valid. As soon as the EOC bit is set the conversion is
completed and the result is valid.
Instead of the polling of the EOC bit one can use a simple delay that should be bigger
than a maximal conversion time (>115 s, see table 4).
Go to the Step 2 to do the next conversion or to the Step 4 to put ADC to the sleep mode.
Step 4 (put ADC to the sleep mode if it’s necessary)
Use SPI to send ADCC instruction (MOSI):
1 0 0 1 x 0 0 0 x x x x x x x x x x x x x x x x
And check 15th bit of the answer (MISO):
0 x x x x x x x x x x x x x x x
If 15
th
bit is zero, the instruction is accepted.
相關PDF資料 |
PDF描述 |
|---|---|
| MM1561FF | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO7 |
| MM1561GF | 1.6 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO7 |
| MM1561HF | 1.7 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO7 |
| MM16ZB-DW-61FA2C | 23 CONTACT(S), MALE, RIGHT ANGLE TWO PART EURO CONNECTOR, SOLDER |
| MM16ZB-DW-61FA3C | 23 CONTACT(S), MALE, RIGHT ANGLE TWO PART EURO CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MLX90614 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614_06 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614AAA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614AAB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614ABA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
發布緊急采購，3分鐘左右您將得到回復。