- 您現在的位置：買賣IC網 > PDF目錄299499 > MLX90609EEA-R2 SPECIALTY ANALOG CIRCUIT, CQCC32 PDF資料下載
參數資料
| 型號： | MLX90609EEA-R2 |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, CQCC32 |
| 封裝： | CERAMIC, LCC-32 |
| 文件頁數： | 22/22頁 |
| 文件大?。?/td> | 550K |
| 代理商： | MLX90609EEA-R2 |
MLX90609
Angular Rate Sensor (Standard version)
390109060901
Page 9 of 22
Data Sheet
Rev 010
November/08
5.2 Communication with the MLX90609 through the SPI
The MLX90609 has a serial communication interface compatible with Serial Peripheral Interface
(SPI). Likewise SPI the Serial Interface of the MLX90609 specifies four signals:
serial clock (SCLK);
master data output, slave data input (MOSI);
master data input, slave data output (MISO); and
slave select (SS ).
The MLX90609 always operates as a slave. Therefore MISO pin is an output only.
The MLX90609 is selected when the SS pin is low (see Figure 5-2). When SS pin is high, data will
not be accepted via the MOSI pin. The serial output pin (MISO) will remain in a high impedance
state. High level of SS forces the serial interface into the start state of data exchange.
Data is serially transmitted to the MLX90609 in 8 bit words (an instruction byte) and in 16 bit data
words. Data is serially received from the MLX90609 in 16 bit words (an answer word). Most
Significant Bit (MSB) is the first bit transmitted and received.
Transmission:
After the device is selected with SS going low, the instruction byte will be received by the
MLX90609. On each rising edge of SCLK data from MOSI enter into an internal 8-bit shift register.
The accepted instruction byte contains the op-code that defines the operations to be performed.
Along with op-code this byte can also contain information such as EEPROM address or ADC mode
(to be setup).
Reception:
After the 8th bit is received to the shift register, the command will be executed by the MLX90609.
The format of the outgoing data is defined by the received instruction. Any instruction evokes an
answer. A full communication cycle (transmitting an instruction and receiving the full answer) is
finished after 24th clock of the SCLK. Communication can be terminated by putting SS high.
Some remarks:
If an invalid op-code is received, it is rejected and the corresponding data is ignored. In this
case a special “refusal answer” will be generated.
It's recommended to use synchronization by SS after every data exchange to prevent a data
distortion.
If high level is applied to SS during an instruction byte transmission, the command will be
ignored.
If high level is applied to SS during the answer reception, the answer will be truncated. This
can be used to limit the reading of the answer to e.g. one byte only (see Figure 5-3).
相關PDF資料 |
PDF描述 |
|---|---|
| MM1561FF | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO7 |
| MM1561GF | 1.6 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO7 |
| MM1561HF | 1.7 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO7 |
| MM16ZB-DW-61FA2C | 23 CONTACT(S), MALE, RIGHT ANGLE TWO PART EURO CONNECTOR, SOLDER |
| MM16ZB-DW-61FA3C | 23 CONTACT(S), MALE, RIGHT ANGLE TWO PART EURO CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MLX90614 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614_06 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614AAA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614AAB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
| MLX90614ABA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single and Dual Zone Infra Red Thermometer |
發布緊急采購，3分鐘左右您將得到回復。