DSI COMMANDS AND RESPONSES SET LOGIC OUT CO" />
參數資料
型號： MCZ33793EF
廠商： Freescale Semiconductor
文件頁數： 13/27頁
文件大?。?/td> 0K
描述： IC DSI SLAVE REMOTE SENS 16-SOIC
標準包裝： 48
類型： 傳感器接口
輸入類型： 邏輯
輸出類型： 邏輯
接口： 并聯
電流 - 電源： 250mA
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 16-SOIC N
包裝： 管件
產品目錄頁面： 808 (CN2011-ZH PDF)
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33793
FUNCTIONAL DEVICE OPERATION
DSI COMMANDS AND RESPONSES
SET LOGIC OUT COMMAND
The Set Logic Out command sets the Logic Out pin to a logic
high. The compliment to this command is the Clear Logic Out.
The Logic Out is cleared at power-up or following a Clear
command. The format of the Clear Logic Out command is
shown in Table 25.
SET LOGIC OUT RESPONSE
This response message is sent during the next message
following a valid Set Logic Out command to the addressed
device. The response is shown in Table 26. No response is
generated if the command address field was $0.
REVERSE INITIALIZATION
The Reverse Initialization is similar to the Initialization
command and will only work under the condition that it has
not already been initialized. The command may be used
three ways. The first is to initialize a programmable address
device. The second is the first step in assigning a pre-
programmed address. The third is to initialize a pre-
programmed device.
For the first case this command is sent to address zero with
the NV bit set to zero. The command will be received by the
next daisy chain device with its bus switch open. Reception
of this command will assign the device address and the group
number. Reception of this command will also cause the bus
switch to close if BS = 1 and no fault is detected.
For the second case the Initialization command is sent the
same as the first except that the NV bit is set to one.
Reception of the command will assign the device address
and the group number and cause the bus switch to close if BS
= 1 and there are no faults. A Read/Write NVM command
then may be sent to complete the setting of a pre-
programmed address.
A pre-programmed device must be initialized by putting its
address in both PA3:PA0 and A3:A0 fields.
Once a device has received a reverse initialization command,
it will ignore further reverse initialization commands or
initialization commands unless it has received a Clear
command or undergone a power-up reset.
The command format is found in Table 27.
Table 25. Set Logic Out Command Format
Data
Address
Command
CRC
-
A3
A2
A1
A0
1
0
1
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The address of the selected device.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
master.
Table 26. Set Logic Out Response Format
High Byte
Low Byte
CRC
A3
A2
A1
A0
0
NV
U
LO
BS
IO3
IO2
IO1
IO0
X3
X2
X1
X0
Legend
A[3:0] - Address bits. The slave address.
BS = Bus Switch Position (1=closed)
IO[3:0] = Values at logic I/Os.
LO = Logic out driven level.
NV = Nonvolatile Memory Write. The value of the NV bit in the slave.
U = Undervoltage indicated true by a “1”.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
slave.
相關PDF資料
PDF描述
MCZ33797EKR2 IC SQUIB DRIVER 2CHAN 32-SOIC
MCZ33884EG IC MULTIPLE CONTACT MON 24-SOIC
MCZ33905BD3EK IC SBC CAN HS 3.3V 54SOIC
MCZ33972EWR2 IC SWITCH DETECTION MULT 32-SOIC
MCZ33975AEKR2 IC SWITCH DETECT MULT ENH 32SOIC
相關代理商/技術參數
參數描述
MCZ33793EFR2 功能描述:輸入/輸出控制器接口集成電路 ORION RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MCZ33797EK 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MCZ33797EKR2 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MCZ33800EK 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33800EKR2 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*