參數資料
型號： MCP9808T-E/MS
廠商： Microchip Technology
文件頁數： 11/52頁
文件大?。?/td> 1085K
描述： IC TEMP SENSOR DGTL I2C 8MSOP
標準包裝： 2,500
功能： 溫度監控系統（傳感器）
傳感器類型： 內部
感應溫度： -40°C ~ 125°C
精確度： ±1°C
拓?fù)洌?/td> ADC（三角積分型），寄存器庫
輸出類型： 2 線串行，I²C?/SMBUS?
輸出警報： 是
輸出風扇： 是
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
?2011 Microchip Technology Inc.
DS25095A-page 11
MCP9808
3.0
PIN DESCRIPTION
The descriptions of the pins are listed in Table 3-1.
3.1
Serial Data Line (SDA)
SDA is a bidirectional input/output pin, used to serially
transmit data to/from the host controller. This pin
requires a pull-up resistor. (See Section 4.0  Serial
Communication.)
3.2
Serial Clock Line (SCL)
The SCL is a clock input pin. All communication and
timing is relative to the signal on this pin. The clock is
generated by the host or master controller on the bus.
(See Section 4.0 Serial Communication.)
3.3
Temperature Alert, Open-Drain
Output (Alert)
The MCP9808 temperature Alert output pin is an
open-drain output. The device outputs a signal when the
ambient temperature goes beyond the user-programmed
temperature limit. (See Section 5.2.3  Alert  Output
Configuration).
3.4
Ground Pin (GND)
The GND pin is the system ground pin.
3.5
Address Pins (A0, A1, A2)
These pins are device address input pins.
The address pins correspond to the Least Significant
bits (LSbs) of the address bits and the Most Significant
bits (MSbs): A6, A5, A4, A3. This is illustrated in
Table 3-2.
3.6
Power Pin (V
DD
)
V
DD
 is the power pin. The operating voltage range, as
specified in the DC electrical specification table, is
applied on this pin.
3.7
Exposed Thermal Pad (EP)
There is an internal electrical connection between the
Exposed Thermal Pad (EP) and the GND pin. The EP
may be connected to the system ground on the Printed
Circuit Board (PCB).
TABLE 3-1:
PIN FUNCTION TABLE
DFN
MSOP
Symbol
Pin Function
1
1
SDA
Serial Data Line
2
2
SCL
Serial Clock Line
3
3
Alert
Temperature Alert Output
4
4
GND
Ground
5
5
A2
Slave Address
6
6
A1
Slave Address
7
7
A0
Slave Address
8
8
V
DD
Power Pin
9

EP
Exposed Thermal Pad (EP); must be connected to GND
TABLE 3-2:
MCP9808 ADDRESS BYTE
Device
Address Code
Slave
Address
A6   A5   A4   A3   A2    A1   A0
MCP9808
0
0
1
1    x
(1)
x
x
MCP9808
(2)
1
0
0
1
x
x
x
Note  1:   User-selectable address is shown by x. 
A2, A1 and A0 must match the
corresponding device pin configuration.
2:   Contact factory for this address code.
相關PDF資料
PDF描述
MCZ33998EGR2 IC REG CHARGEPUMP/LINEAR 24SOIC
MCZ34652EFR2 IC HOTSWAP CTRLR 2A NEG 16SOIC
MCZ34653EFR2 IC HOTSWAP CTRLR 1A NEG 8-SOIC
MCZ34670EG IC POE CURR MODE SW REG 20-SOIC
MIC184BM TR IC SUPERVISOR LOCAL/REMOTE 8SOIC
相關代理商/技術參數
參數描述
MCP98242 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD
MCP98242_09 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD
MCP98242-BE/MC 制造商:Microchip Technology Inc 功能描述:TEMP SENSOR DGTL SERL (2-WIRE, - Bulk
MCP98242-BE/MNY 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD
MCP98242-BE/ST 功能描述:板上安裝溫度傳感器 JEDEC DIMM Serial output temp sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*