- 您現在的位置：買賣IC網 > PDF目錄1953 > MCP2150T-I/SO (Microchip Technology)IC IRDA STD CONTROLLER 18SOIC PDF資料下載
參數資料
| 型號： | MCP2150T-I/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 50/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC IRDA STD CONTROLLER 18SOIC |
| 標準包裝： | 1,100 |
| 控制器類型： | IRDA 標準協議?？刂破?br> |
| 接口： | UART |
| 電源電壓： | 3 V ~ 5.5 V |
| 電流 - 電源： | 7mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 18-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 18-SOIC |
| 包裝： | 帶卷 (TR) |
| 配用： | MCP215XDM-ND - BOARD DEMO FOR MCP215X |
| 其它名稱： | MCP2150TI/SO |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁
2002 Microchip Technology Inc.
Preliminary
DS21655B-page 7
MCP2150
2.0
DEVICE OPERATION
The MCP2150 is a cost effective, low pin count (18-
pin), easy to use device for implementing IrDA stan-
dard wireless connectivity. The MCP2150 provides
support for the IrDA standard protocol “stack” plus bit
encoding/decoding. The Serial interface and IR baud
rates are independantly selectable.
2.1
Power Up
Any time the device is powered up (parameter D003),
the Power Up Timer delay (parameter 33) occurs, fol-
lowed by an Oscillator Start-up Timer (OST) delay
(parameter 32). Once these delays complete, commu-
nication with the device may be initiated. This commu-
nication is from both the infrared transceiver’s side as
well as the controller’s UART interface.
2.2
Device Reset
The MCP2150 is forced into the reset state when the
RESET pin is in the low state. Once the RESET pin is
brought to a high state, the Device Reset sequence
occurs. Once the sequence completes, functional
operation begins.
2.3
Clock Source
The MCP2150 requires a clock source to operate. The
frequency of this clock is 11.0592 MHz (electrical spec-
ification parameter 1A). This clock can be supplied by
either a crystal/resonator or as an external clock input.
2.3.1
CRYSTAL OSCILLATOR / CERAMIC
RESONATORS
A crystal or ceramic resonator can be connected to the
OSC1 and OSC2 pins to establish oscillation
(Figure 2-1). The MCP2150 oscillator design requires
the use of a parallel cut crystal. Use of a series cut crys-
tal may give a frequency outside of the crystal
manufacturers specifications.
FIGURE 2-1:
CRYSTAL OPERATION
(OR CERAMIC
RESONATOR)
TABLE 2-1:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
TABLE 2-2:
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
2.3.2
EXTERNAL CLOCK IN
For applications where a clock is already available
elsewhere, users may directly drive the MCP2150 pro-
vided that this external clock source meets the AC/DC
timing requirements listed in Section 4.3. Figure 2-2
shows how an external clock circuit should be
configured.
FIGURE 2-2:
EXTERNAL CLOCK INPUT
OPERATION
C1 and C2.
Note:
A series resistor may be required for AT
strip cut crystals.
C1
C2
XTAL
OSC2
RS
OSC1
RF
To internal
MCP2150
Note
logic
Freq
OSC1 (C1)
OSC2 (C2)
11.0592 MHz
10 - 22 pF
Higher capacitance increases the stability of the oscil-
lator but also increases the start-up time. These val-
ues are for design guidance only. Since each
resonator has its own characteristics, the user should
consult the resonator manufacturer for appropriate
values of external components.
Freq
OSC1 (C1)
OSC2 (C2)
11.0592 MHz
15 - 30 pF
Higher capacitance increases the stability of the oscil-
lator but also increases the start-up time. These val-
ues are for design guidance only. RS may be required
to avoid overdriving crystals with low drive level spec-
ification.
Since
each
crystal
has
its
own
characteristics, the user should consult the crystal
manufacturer for appropriate values of external
components.
Clock From
external
MCP2150
OSC1
OSC2
Open
system
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2155-I/SS | IC IRDA PROTOCOL CTRLR 20SSOP |
| MCP2200-I/MQ | IC USB TO UART 20QFN |
| MCP2200T-I/MQ | IC USB 2.0 - UART 20QFN |
| MCP2210T-I/MQ | IC CONVERTER USB-PCI 20-QFN |
| MCP23008-E/ML | IC I/O EXPANDER I2C 8B 20QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2155 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Infrared Encoder/Decoder |
| MCP2155_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IrDA?? Standard Protocol Stack Controller |
| MCP2155-I/P | 功能描述:網絡控制器與處理器 IC IrDA protocol handlr RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2155-I/P | 制造商:Microchip Technology Inc 功能描述:Infrared Encoder/Decoder IC |
| MCP2155-I/SO | 功能描述:網絡控制器與處理器 IC IrDA protocol handlr RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。