參數資料
型號： MCF5471ZP200
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 32-BIT, 200 MHz, RISC PROCESSOR, PBGA388
封裝： 27 X 27 MM, 1 MM PITCH, PLASTIC, MS-034AAL-1, BGA-388
文件頁數： 33/96頁
文件大?。?/td> 2003K
代理商： MCF5471ZP200
MOTOROLA
MCF547x Integrated Microprocessor Hardware Specifications
39
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
Signal Description
In slave mode, the SS signal is a slave select input signal that allows an SPI master to select the DSPI as the
target for transmission.
1.5.1.9.5
DSPI Chip Selects (DSPICS[2:3])
The synchronous peripheral chip selects (DSPICS[2:3]) outputs provide DSPI peripheral chip selects that
can be programmed to be active high or low.
1.5.1.9.6
DSPI Peripheral Chip Select 5/Peripheral Chip Select Strobe
(DSPICS5/PCSS)
DSPICS5 is a peripheral chip select output signal. When the DSPI is in master mode and the
DMCR[PCSSE] bit is cleared, this signal is used to select which slave device the current transfer is intended
for.
PCSS provides a strobe signal that can be used with an external demultiplexer for deglitching of the
DSPICSn signals. When the DSPI is in master mode and DMCR[PCSSE] is set, the PCSS provides the
appropriate timing for the decoding of the DSPICS[0,2,3] signals which prevents glitches from occurring.
This signal is not used in slave mode.
1.5.1.10 I2C I/O SIGNALS
The I2C serial interface module uses the signals in this section.
1.5.1.10.1 Serial Clock (SCL)
This bidirectional open-drain signal is the clock signal for the I2C interface. It is either driven by the I2C
module when the bus is in master mode or it becomes the clock input when the I2C is in slave mode.
1.5.1.10.2 Serial Data (SDA)
This bidirectional open-drain signal is the data input/output for the I2C interface.
1.5.1.11 PSC Module Signals
The PSC modules use the signals in this section. The baud rate clock inputs are not supported.
1.5.1.11.1 Transmit Serial Data Output (PSC0TXD, PSC1TXD, PSC2TXD,
PSC3TXD)
PSCnTXD are the transmitter serial data outputs for the PSC modules. The output is held high (mark
condition) when the transmitter is disabled, idle, or in the local loopback mode. The PSCxTXD pins can be
programmed to be driven low (break status) by a command.
1.5.1.11.2 Receive Serial Data Input (PSC0RXD, PSC1RXD, PSC2RXD,
PSC3RXD)
PSCnRXD are the receiver serial data inputs for the PSC modules. When the PSC clock is stopped for
power-down mode, any transition on the pins restarts them.
相關PDF資料
PDF描述
MCF5472VR200 32-BIT, 200 MHz, RISC PROCESSOR, PBGA388
MCF5475VR266 32-BIT, 266.66 MHz, RISC PROCESSOR, PBGA388
MCF5470ZP200 32-BIT, 200 MHz, RISC PROCESSOR, PBGA388
MCF5475ZP266 32-BIT, 266.66 MHz, RISC PROCESSOR, PBGA388
MCF5471ZP200 32-BIT, 200 MHz, RISC PROCESSOR, PBGA388
相關代理商/技術參數
參數描述
MCF5472 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MCF547x Integrated Microprocessor Electrical Characteristics
MCF5472EC 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MCF547x ColdFire Microprocessor
MCF5472VR200 功能描述:微處理器 - MPU MCF547X V4ECORE MMU FPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MCF5472ZP200 功能描述:微處理器 - MPU MCF547X V4ECORE MMU FPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MCF5473 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MCF547x Integrated Microprocessor Electrical Characteristics
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*