參數資料
型號: MC3PHACVDW
廠商: MOTOROLA INC
元件分類: 運動控制電子
英文描述: 3-Phase AC Motor Controller
中文描述: AC MOTOR CONTROLLER, PDSO28
封裝: PLASTIC, SOIC-28
文件頁數: 21/44頁
文件大小: 724K
代理商: MC3PHACVDW
MC3PHAC/D
Operation
MOTOROLA
3-Phase AC Motor Controller
21
Standalone Operation
If the VBOOST_MODE pin is high when the MC3PHAC is powered up, or after
a reset, the MC3PHAC enters standalone mode. In this mode of operation, the
functionality of many of the MC3PHAC pins change so that the device can
control a motor without requiring setup information from an external master.
When operated in standalone mode, the MC3PHAC will drive certain pins
corresponding to parameters which must be specified, while simultaneously
monitoring the response on other pins.
In many cases, the parameter to be specified is represented as an analog
voltage presented to the MUX_IN pin, while certain other pins are driven low.
In so doing, the MC3PHAC can accommodate an external analog mux which
will switch various signals on the MUX_IN pin when the signal select line goes
low. All signals must be in a range between 0 V and V
REF
. As an economical
alternative, an external passive network can be connected to each of the
parameter select output pins and the MUX_IN pin, as shown in
Figure 8
.
The Thevenin equivalent impedance of this passive network as seen by the
MUX_IN pin is very important and should be in the range of 5 k
to 10 k
. If
the resistance is too high, leakage current from the input/output (I/O) pins will
cause an offset voltage that will affect the accuracy of the reading. If the
resistance is too low, the parameter select pins will not be able to sink the
required current for an accurate reading. Using a pullup resistor value of 6.8 k
(as indicated in
Figure 8
), the resulting value for each parameter as a function
of the corresponding pulldown resistor value is shown in
Figure 9
,
Figure 10
,
Figure 11
, and
Table 4
.
The START
input pin is debounced internally and a switch can be directly
accommodated on this pin. The input is level sensitive, but a logic 1 level must
exist on the pin before a logic 0 level will be processed as a start signal. This
will prevent an accidental motor startup in the event of the MC3PHAC being
powered up, where the switch was left in the start position.
The FWD input pin is debounced internally and can directly accommodate a
switch connection. The input is also level sensitive.
Figure 8
shows the jumper arrangement connected to the
PWMPOL_BASEFREQ input pin. For proper operation, one and only one
jumper connection can be made at any given time.
Table 3
shows the polarity
and base frequency selections as a function of the jumper connection.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC3PHACVFA 3-Phase AC Motor Controller
MC3PHACVP 3-Phase AC Motor Controller
MC3S12C128 16-Bit Microcontroller
MC3S12C32 16-Bit Microcontroller
MC3S12C64 16-Bit Microcontroller
相關代理商/技術參數
參數描述
MC3PHACVDWE 功能描述:馬達/運動/點火控制器和驅動器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC3PHACVFA 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 32LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:8BIT MCU, 8K FLASH OTP - Bulk
MC3PHACVFAE 功能描述:馬達/運動/點火控制器和驅動器 8B MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC3PHACVP 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC
MC3PHACVPE 功能描述:馬達/運動/點火控制器和驅動器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube