參數資料
型號： MC33389DDW
廠商： Freescale Semiconductor
文件頁數： 13/49頁
文件大?。?/td> 0K
描述： IC SYSTEM BASE W/CAN 28-SOIC
標準包裝： 1
控制器類型： 系統基礎芯片
接口： CAN
電源電壓： 5.5 V ~ 18 V
電流 - 電源： 45mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 管件
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33389
FUNCTIONAL DEVICE OPERATION
speed applications up to 125 kBit/s in passenger cars. It
provides differential transmission capability, but will switch in
error condition to single wire transmitter and/or receiver.
The rise and fall slopes are limited to reduce radio
frequency interference (RFI). This provides use of an
unshielded twisted pair or a parallel pair of wires for the bus.
It supports transmission capability on either bus wire if one of
the bus wire is corrupted. The logic failure detection
automatically selects a suitable transmission mode.
In a normal operation (no wiring failures), the differential
bus state is the output to RX. The differential receiver inputs
are connected to CANH and CANL through integrated filters.
The filtered inputs signals are also used for the single wire
receivers. The CANH and CANL receivers have threshold
voltages, assuring maximum noise margin in single wire
modes. In the RX Only mode, the transmitter is disabled;
however, the receive part of the transceiver remains active. In
this mode, RX reports bus and TX activity (RX = TX or Bus
dominant). Failure detection and management is the same as
the Bus Normal mode.
Failure Detector
The failure detector is active in RXTX and RX Only
operation modes. The detector recognizes the following
single bus failures and switches to an appropriate mode.
1. CANH wire interrupted
2. CANL wire interrupted or shorted to 5.0 V
3. CANH short-circuit to battery
4. CANL short-circuit to ground
5. CANH short-circuit to ground
6. CANL short-circuit to battery
7. CANL mutually shorted to CANH
8. CANH to V2 (5.0 V)
Note: Shorts-circuit failures are detected for 0 to 50
shorts.
The differential receiver (CANH-CANL) threshold is set at
-2.8 V, this assures a proper reception in the normal
operating modes. In case of failures 1, 2, and 5 the on-going
message is not destroyed due to noise margin.
Failures 3 and 6 are detected by comparators respectively
connected to CANH and CANL. If the comparator threshold
is exceeded for a certain time (TAC3D, TAC6D), the reception
is switched to single wire mode. This time is required to avoid
false triggering by external RF fields. Recovery from these
failures is detected automatically after a certain (TAC3R,
TAC6R) time-out (filtering).
Failures 4 and 7 initially result in a permanent dominant
level at RX. After a time-out, the CANL driver and the RTL
pins are switched OFF. Only a weak pull-up at CANL
remains. Reception continues by switching to Single Wire
mode through CANH. When Failures 4 or 7 are removed, the
recessive bus levels are restored. If the differential voltage
remains below the recessive threshold for a certain (TAC478R)
time, reception and transmission switch back to the
Differential mode.
If any of the eight wiring failure occurs, a flag is set in the
TESRH and TESRL Status registers. Eight different types of
errors are distinguished out of these eight errors. They are
separately stored in these register. Please refer to the
Tables 35 and 36. A maskable interrupt is sent to the
microcontroller. On error recovery, the corresponding flag is reset
after read-out operation.
During all single wire transmissions, the EMC performance
(both immunity and emission) is worse than in the Differential
mode. Integrated receiver filters suppress any high frequency
noise induced into the bus wires. The cut-off frequency of
these filters is a compromise between propagation delay and
high frequency suppression. In the Single Wire mode, low
frequency noise can not be distinguished from the expected
signal.
In the event of a permanent dominant TX state (for more
than 2.0 ms) the output drivers are disabled. That assures the
operation of the complete system in case of a permanent
dominant TX state of one control unit. The CAN interface of a
defective ECU, which has TX permanently low, will
automatically be set to the receive only mode and therefore
will not lock the complete CAN bus.
Protection
A current limiting circuit protects the transmitter output
stages against short-circuit to positive and negative battery
voltage. If the junction temperature exceeds a maximum
value, the transmitter output stages are disabled. Because
the transmitter is responsible for a part of the power
dissipation, this results in a reduced power dissipation
resulting in a lower chip temperature. All other parts of the
transceiver will remain operating. The CANH and CANL
inputs are protected against electrical transients, and may
occur in an automotive environment.
Thermal Management
The 33389 is proposed in two different packages:
1. HSOP-20 for high power applications
2. SO28WB with eight pins to the lead frame for medium
power applications
HSOP20 Package
For such a package, the heat flow is mainly vertical and
each heat source (dissipating element) can be seen as an
independent thermal resistance to the Heatsink. The thermal
network can be roughly depicted in Figure 6.
相關PDF資料
PDF描述
MC33394DH IC POWER SUPPLY MULT-OUT 44-HSOP
MC33560DW OC PWR MGMT READERS/CPLR 24-SOIC
MC33689DDWBR2 IC SYSTEM BASE W/LIN 32-SOIC
MC33742EPR2 IC SYSTEM BASE W/CAN 48-QFN
MC33780EG IC DBUS MASTER DUAL DIFF 16-SOIC
相關代理商/技術參數
參數描述
MC33389DDWR2 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33390D 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC33390DR2 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC33390EF 制造商:Freescale Semiconductor 功能描述:
MC33394DH 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*