- 您現在的位置：買賣IC網 > PDF目錄385564 > MC12U064DACA-2QC00 (SAMSUNG SEMICONDUCTOR CO. LTD.) Dual Voltage MultiMediaCard Specification PDF資料下載
參數資料
| 型號： | MC12U064DACA-2QC00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | Dual Voltage MultiMediaCard Specification |
| 中文描述： | 雙電壓多媒體卡規格 |
| 文件頁數： | 50/64頁 |
| 文件大?。?/td> | 1385K |
| 代理商： | MC12U064DACA-2QC00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MultiMediaCard
TM
to be sent from the host. CRC suffix, block length and start address restrictions are identical to the read
operation (see Figure 46). If a CRC error is detected it will be reported in the data-response token and
the data block will not be programmed. Every data block has a prefix of ‘Start Block’ token (one byte).
After a data block has been received, the card will respond with a data-response token. If the data block
has been received without errors, it will be programmed. As long as the card is busy programming, a
continuous stream of busy tokens will be sent to the host (effectively holding the DataOut line low).
Figure 4-6 Single Block Write Operation
In Multiple Block write operation the stop transmission will be done by sending ‘Stop Tran’ token instead
of ‘Start Block’ token at the beginning of the next block.
Two types of multiple block write transactions, identical to the multiple block read, are defined (the host
can use either one at any time):
* Open-ended Multiple block write
The number of blocks for the write multiple block operation is not defined. The card will continuously
accept and program data blocks until a ‘Stop Tran’ token is received.
* Multiple block write with pre-defined block count
The card will accept the requested number of data blocks and terminate the transaction. ‘Stop tran’ token
is not required at the end of this type of multiple block write, unless terminated with an error. In order to
start a multiple block write with pre-defined block count the host must use the SET_BLOCK_COUNT
command (CMD23) immediately preceding the WRITE_MULTIPLE_BLOCK (CMD25) command.
Otherwise the card will start an open-ended multiple block write which can be stopped using the ‘Stop
tran’ token.
The host can abort writing at any time, within a multiple block operation, regardless of the its type.
Transaction abort is done by sending the ‘Stop tran’ token. If a multiple block write with pre-defined block
count is aborted, the data in the remaining blocks is not defined.
If the card detects a CRC error or a programming error (e.g. write protect violation, out of range, address
misalignment, internal error, etc.) during a multiple block write operation (both types) it will report the
failure in the data-response token and ignore any further incoming data blocks. The host must than abort
the operation by sending the ‘Stop Tran’ token.
50
相關PDF資料 |
PDF描述 |
|---|---|
| MC12U128DACA-2QC00 | Dual Voltage MultiMediaCard Specification |
| MC14024B | 7 Stage Ripple Counter(7位二進制計數器) |
| MC14029B | Binary/Decade Up/Down Counter(二/十進制 增/減計數器) |
| MC1403B | Low Voltage Reference(低電壓參考源) |
| MC1403 | Low Voltage Reference(低電壓參考源) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC12U064HACA | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HACC-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC12U064HAFA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。