- 您現在的位置：買賣IC網 > PDF目錄45193 > MB91F313APMC-GE1 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91F313APMC-GE1 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-120 |
| 文件頁數： | 11/72頁 |
| 文件大小： | 1843K |
| 代理商： | MB91F313APMC-GE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MB91313A Series
DS07-16706-4E
19
Notes on the turning on/off VDDI pin (1.8 V internal power supply) and VDDE pin (3.3 V external pin power
supply)
Do not apply only VDDE pin (external power supply) voltage continuously (more than one minute) while the
VDDI pin (internal power supply) is disconnected as it will adversely affect the reliability of the LSI.
When the VDDE pin (external power supply) returns from the off state to the on state, the circuit may not be
able to maintain its internal state, for example, due to power supply noise.
Turning on/off these power supplies (VDDI/Analog/VDDE) simultaneously causes no problem.
When the power is turned on, the states of the output pins may remain undefined until the internal power
supply becomes stable.
Notes on using an external clock
When using the external clock as a general rule you should simultaneously supply X0 (X0A) and X1 (X1A)
pins. And also, the clock signal to X0 (X0A) should be supplied a clock signal with the reverse phase to X1
(X1A) pins. However, in this case the stop mode (oscillation stop mode) must not be used (This is because
the X1 (X1A) pin stops at “H” output in STOP mode). Furthermore, supply a clock to X0 (X0A) pin only if the
device is operating in less than 12.5 MHz.
Note : When operating at a frequency of 10 MHz, the delay between the X0 (X0A) and X1 signals should be
less than 15 ns.
Power on
VDD pin (internal power supply)
→ VDDE pin (external power supply) → Analog→ Signal
Power off
Signal
→ Analog→ VDDE pin (external power supply) → VDDI pin (internal power supply)
X0, X0A
X1, X1A
Cannot be used in STOP mode (oscillation stop mode).
MB91313A series
Using an External Clock (Normal Method)
X0, X0A
X1, X1A
Open
MB91313A series
Using an External Clock (available at 12.5 MHz or less)
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F345BPFT-GE1 | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F355APMT | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F365GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F366GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F368GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F314 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F314PMC-GE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F318A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F318R | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F318RPMC-G-XXXE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。