參數資料
型號： MAX9995ETX-TD
廠商： Maxim Integrated Products, Inc.
英文描述： Dual, SiGe, High-Linearity, 1700MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch
中文描述： 雙通道，鍺，高線性度，1700MHz至2200MHz下變頻混頻器，LO緩沖器/開關
文件頁數： 11/13頁
文件大小： 363K
代理商： MAX9995ETX-TD
internal LO SPDT switch that can be used for frequen-
cy-hopping applications. The switch selects one of the
two single-ended LO ports, allowing the external oscil-
lator to settle on a particular frequency before it is
switched in. LO switching time is typically less than
50ns, which is more than adequate for virtually all GSM
applications. If frequency hopping is not employed, set
the switch to either of the LO inputs. The switch is con-
trolled by a digital input (LOSEL): logic high selects
LO1, and logic low selects LO2. LO1 and LO2 inputs
are internally matched to 50
, requiring only a 22pF
DC-blocking capacitor.
A two-stage internal LO buffer allows a wide input
power range for the LO drive. All guaranteed specifica-
tions are for an LO signal power from -3dBm to +3dBm.
The on-chip low-loss balun, along with an LO buffer,
drives the double-balanced mixer. All interfacing and
matching components from the LO inputs to the IF out-
puts are integrated on-chip.
High Linearity Mixers
The core of the MAX9995 is a pair of double-balanced,
high-performance passive mixers. Exceptional linearity
is provided by the large LO swing from the on-chip LO
buffer. When combined with the integrated IF ampli-
fiers, the cascaded IIP3, 2RF-2LO rejection, and NF
performance is typically +25.6dBm, 66dBc, and 9.8dB,
respectively.
Differential IF Output Amplifiers
The MAX9995 mixers have an IF frequency range of
40MHz to 350MHz. The differential, open-collector IF
output ports require external pullup inductors to V
CC
.
Note that these differential outputs are ideal for provid-
ing enhanced 2RF-2LO rejection performance. Single-
ended IF applications require a 4:1 balun to transform
the 200
differential output impedance to a 50
single-
ended output. After the balun, VSWR is typically 1.5:1.
Applications Information
Input and Output Matching
The RF and LO inputs are internally matched to 50
.
No matching components are required. Return loss at
each RF port is typically 14dB over the entire input
range (1700MHz to 2200MHz), and return loss at the
LO ports is typically 18dB (1400MHz to 2000MHz). RF
and LO inputs require only DC-blocking capacitors for
interfacing.
The IF output impedance is 200
(differential). For
evaluation, an external low-loss 4:1 (impedance ratio)
balun transforms this impedance down to a 50
single-
ended output (see the
Typical Application Circuit
).
Bias Resistors
Bias currents for the LO buffer and the IF amplifier are
optimized by fine tuning the resistors R1, R2, R4, and R5.
If reduced current is required at the expense of perfor-
mance, contact factory. If the
±
1% bias resistor values
are not readily available, substitute standard
±
5% values.
Layout Considerations
A properly designed PC board is an essential part of
any RF/microwave circuit. Keep RF signal lines as short
as possible to reduce losses, radiation, and induc-
tance. For the best performance, route the ground pin
traces directly to the exposed pad under the package.
The PC board exposed pad
MUST
be connected to the
ground plane of the PC board. It is suggested that mul-
tiple vias be used to connect this pad to the lower-level
ground planes. This method provides a good RF/ther-
mal-conduction path for the device. Solder the exposed
pad on the bottom of the device package to the PC
board. The MAX9995 Evaluation Kit can be used as a
reference for board layout. Gerber files are available
upon request at www.maxim-ic.com.
Power-Supply Bypassing
Proper voltage-supply bypassing is essential for high-
frequency circuit stability. Bypass each V
CC
pin with a
capacitor as close to the pin as possible (
Typical
Application Circuit
).
Exposed Pad RF/Thermal Considerations
The exposed paddle (EP) of the MAX9995’s 36-pin thin
QFN-EP package provides a low thermal-resistance
path to the die. It is important that the PC board on
which the MAX9995 is mounted be designed to con-
duct heat from the EP. In addition, provide the EP with
a low-inductance path to electrical ground. The EP
MUST
be soldered to a ground plane on the PC board,
either directly or through an array of plated via holes.
Chip Information
TRANSISTOR COUNT: 1414
PROCESS: SiGe BiCMOS
M
Dual, SiGe, High-Linearity, 1700MHz to 2200MHz
Downconversion Mixer with LO Buffer/Switch
______________________________________________________________________________________
11
相關PDF資料
PDF描述
MAX9995ETX Dual, SiGe, High-Linearity, 1700MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch
MAX9995 Hex 2-Input NOR Drivers 20-CDIP -55 to 125
MBA-9 Frequency Mixer
MBD110DWT1G Dual Schottky Barrier Diodes
MBD330DWT1G Dual Schottky Barrier Diodes
相關代理商/技術參數
參數描述
MAX9995EVKIT 功能描述:射頻開發工具 RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
MAX9996ETP 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
MAX9996ETP+ 功能描述:上下轉換器 SiGe 1700-2200MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128
MAX9996ETP+D 功能描述:上下轉換器 SiGe 1700-2200MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128
MAX9996ETP+G48 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*