參數資料
型號： MAX9767ETJ+
廠商： Maxim Integrated Products
文件頁數： 8/33頁
文件大?。?/td> 0K
描述： IC AMP AUDIO .75W STER AB 32TQFN
標準包裝： 60
類型： AB 類
輸出類型： 2 通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 750mW x 2 @ 4 歐姆
電源電壓： 2.7 V ~ 5.5 V
特點： 消除爆音，麥克風，靜音，短路保護和熱保護，關機
安裝類型： 表面貼裝
供應商設備封裝： 32-TQFN-EP（5x5）
封裝/外殼： 32-WFQFN 裸露焊盤
包裝： 管件
MAX9765/MAX9766/MAX9767
750mW Audio Amplifiers with Headphone Amp,
Microphone Preamp, and Input Mux
16
______________________________________________________________________________________
Detailed Description
The MAX9765/MAX9766/MAX9767 feature 750mW BTL
speaker amplifiers, 65mW headphone amplifiers, input
multiplexers, headphone sensing, differential and sin-
gle-ended input microphone amplifiers, and compre-
hensive click-and-pop suppression. The MAX9765/
MAX9766 are controlled through an I2C-compatible, 2-
wire serial interface. The MAX9767 is controlled
through three logic inputs: MUTE, SHDN, INT (see the
Selector Guide). The MAX9765 family features excep-
tional PSRR (95dB at 1kHz), allowing these devices to
operate from noisy digital supplies without the need for
a linear regulator.
The speaker amplifiers use a BTL configuration. The
MAX9765/MAX9766 main amplifiers are composed of
an input amplifier and an output amplifier. Resistor RIN
sets the input amplifier’s gain, and resistor RF sets the
output amplifier’s gain. The output of these two ampli-
fiers serves as the input to a slave amplifier configured
as an inverting unity-gain follower. This results in two
outputs, identical in magnitude, but 180° out of phase.
The overall gain of the speaker amplifiers is twice the
product of the two amplifier gains (see the Gain-Setting
Resistor section). A unique feature of this architecture
is that there is no phase inversion from input to output.
The MAX9767 does not use a two-stage input amplifier
and therefore has phase inversion from input to output.
When configured as a headphone (single-ended) ampli-
fier, the slave amplifier is disabled, muting the speaker
and the main amplifier drives the headphone. The
MAX9765/MAX9766/MAX9767 can deliver 700mW of
continuous average power into a 4 load with less than
1% THD+N in speaker mode. The MAX9765/MAX9766
can deliver 70mW of continuous average power into a
16 load with less than 1% THD+N in headphone
mode. The speaker amplifiers also feature thermal-
overload and short-circuit current protection.
All devices feature microphone amplifiers with both dif-
ferential and single-ended inputs. Differential input is
intended for use with internal microphones. Single-
ended input is intended for use with external (auxiliary)
microphones. The differential input configuration is par-
ticularly effective when layout constraints force the
microphone amplifier to be physically remote from the
ECM microphone and/or the rest of the audio circuitry.
The MAX9766/MAX9767 feature a complementary out-
put, creating an ideal interface with CODECs and other
devices with differential inputs. All devices also feature
an internal microphone bias generator.
Amplifier Common-Mode Bias
These devices feature an internally generated com-
mon-mode bias voltage of 1.5V referenced to GND.
BIAS provides both click-and-pop suppression and
sets the DC bias level for the audio signal. BIAS is inter-
nally connected to the noninverting input of each
speaker amplifier (see the Typical Application Circuit).
Choose the value of the bypass capacitor as described
in the BIAS Capacitor section.
Input Multiplexer
The MAX9765/MAX9766 feature a 2:1 input multiplexer
on the front end of each amplifier. The multiplexer is
controlled by bit 1 in the control register. A logic low
Pin Description (continued)
PIN
MAX9765
MAX9766
MAX9767
NAME
FUNCTION
—19
17
MICOUT-
Microphone Amplifier Negative Output
—
23
—
GAINM
—
9
INL
Left-Channel Input
——
25
INT/EXT
Internal (Differential) or External (Single-Ended) Input Select. Drive
INT/EXT
low to select internal or high to select external microphone amplifier.
——
26
MICGAIN
Microphone Amplifier Gain Set. Tri-State Pin. Connect to VDD for gain = 10dB,
float for gain = 20dB, and to GND for gain = 30dB.
—
28
INR
Right-Channel Input
—
30
MUTE
Mute Input
—
EP
Exposed Pad. Connect to ground plane of PC board to optimize heatsinking.
相關PDF資料
PDF描述
MS27468E11F98P CONN RCPT 6POS JAM NUT W/PINS
MAX4367ETA+T IC AMP AUDIO PWR .33W MONO 8TDFN
MS27505E11F13PA CONN RCPT 13POS BOX MNT W/PINS
LTC1407ACMSE-1#TRPBF IC ADC 14BIT 3MSPS SAMPLE 10MSOP
MAX9762ETI+T IC AMP AUDIO PWR 3W MONO 28TQFN
相關代理商/技術參數
參數描述
MAX9767ETJ+ 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9767ETJ+T 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9767ETJ-T 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9768BETG+ 功能描述:音頻放大器 10W Mono Class D Speaker RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9768BETG+T 功能描述:音頻放大器 10W Mono Class D Speaker RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*