- 您現在的位置：買賣IC網 > PDF目錄2158 > MAX9643UATA+T (Maxim Integrated Products)IC AMP CURR SENSE 60V HS 8-TDFN PDF資料下載
參數資料
| 型號： | MAX9643UATA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/12頁 |
| 文件大小： | 0K |
| 描述： | IC AMP CURR SENSE 60V HS 8-TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 電流檢測 |
| 電路數： | 1 |
| 轉換速率： | 12 V/µs |
| 增益帶寬積： | 10MHz |
| 電流 - 輸入偏壓： | 35µA |
| 電壓 - 輸入偏移： | 10µV |
| 電流 - 電源： | 1mA |
| 電流 - 輸出 / 通道： | 3.4A |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 36 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN-EP（2x3） |
| 包裝： | 帶卷 (TR) |
MAX9643
60V High-Speed Precision Current-Sense Amplifier
9
Maxim Integrated
Detailed Description
The MAX9643 is a high-speed precision current-sense
amplifier ideal for a wide variety of high-performance
industrial and automotive power-supply applications. The
device’s low input offset voltage, tight gain error, and low
temperature drift characteristics allow the use of small-
sense resistors for current measurements to improve
power-supply conversion efficiency and accuracy of mea-
surements. Its fast response allows it to react quickly to
switching currents as is common in power-supply circuits,
and makes it possible to be used as part of control loops.
The unidirectional high-side, current-sense amplifier
also features a wide -1.5V to +60V input common-mode
range. This feature allows monitoring of power-supply
load current even if the rail is shorted to ground. High-
side current monitoring does not interfere with the ground
path of the load being measured, making the IC particu-
larly useful in a wide range of high-reliability systems.
The IC has been designed on a proprietary high-speed
complementary BiCMOS SOI process. This high-voltage
analog process is optimized for excellent AC dynamic
performance, ultra-low noise, wide operating voltage
range, and low-drift signal conditioning circuitry.
Applications Information
Internal Charge Pump
An internal charge pump on the part is utilized to provide
two attractive application features:
U
Input common-mode voltage range extends to 1.5V
below ground.
U
Output voltage range extends down to true ground.
A 250kHz internal charge pump is used to generate a
negative voltage rail to bias both the input stage and
output stage of the current-sense amplifier. Use a 1FF
ceramic capacitor between the CP1 and CP2 pins of the
IC, and ensure a tight layout to minimize loop area. Using
a 1FF ceramic capacitor from VEE to GND is essential to
good low-noise performance.
It is possible to also connect the VEE pin directly to an
external -5V power supply. Ensure that this voltage is
lower than the internally generated charge-pump voltage.
The -4.7V voltage is the minimum necessary to guarantee
the charge pump is turned off.
The MAX9643 EV kit shows a good example layout. A
representation is shown in Figure 1.
Input Common-Mode Voltage Range
The use of an internal negative voltage rail for its
input stage allows the current-sense amplifier to extend
its input common-mode voltage below ground without
any crossover inaccuracies. Crossover problems with
precision can occur with alternate architectures of
current-sense amplifiers that use two different input
differential stages to cover the entire operating common-
mode voltage range (either npn/pnp transistors or pnp
transistor and resistor-based input stages).
The minimum input common-mode voltage capability
is dependent on the internal negative voltage rail gener-
ated by the charge pump. Since this negative voltage rail
goes down at low values of VCC (i.e., when under 5V), the
minimum input common-mode voltage rail is also limited
at low VCC.
The negative input common-mode voltage specification
can be exceeded if the input current is limited to under
5mA. This is typically accomplished by using series
input resistors. The input ESD structure for negative input
common-mode voltages looks like 5 series-connected
diodes. Assuming an on-drop of 0.7V per diode, negative
Figure 1. PCB Layout
1
+
34
86
5
MAX9643
2
7
FROM RSENSE
TO ADC
0.1F
1F
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9913EUB+T | IC OP AMP R-R I/O 10-UMAX |
| MAX9917EUB+T | IC OP AMP R-R I/O 10-UMAX |
| MAX9919NASA+T | IC AMP CURRENT SENSE 8SOIC |
| MAX9923TEUB+ | IC AMP CURRENT SENSE 10-MSOP |
| MAX9929FAUA+T | IC AMP CURRENT SENSE 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9644EBS+TG45 | 功能描述:校驗器 IC Low-Power Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9644EUK+T | 功能描述:校驗器 IC Low-Power Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9644EVKIT# | 功能描述:其他開發工具 MAX9644 Eval Kit RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓: |
| MAX9644EVKIT+ | 功能描述:其他開發工具 MAX9644 Eval Kit RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓: |
| MAX9645EBS+TG45 | 功能描述:校驗器 IC Low-Power Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。