- 您現在的位置：買賣IC網 > PDF目錄11688 > MAX9273GTL+T (Maxim Integrated Products)IC SERIALIZER 22BIT GMSL 40TQFN PDF資料下載
參數資料
| 型號： | MAX9273GTL+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 32/49頁 |
| 文件大小： | 0K |
| 描述： | IC SERIALIZER 22BIT GMSL 40TQFN |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
MAX9273
22-Bit GMSL Serializer with Coax or
STP Cable Drive
38
Maxim Integrated
serializer follows the transition of LOCK at GPI. If other
sources also use the GPI input, the FC can implement
a routine to distinguish between interrupts from loss-of-
lock and normal interrupts. The control channel does not
require an active video link and thus can always monitor
LOCK. LOCK asserts for a synchronized video link but
not for the configuration link.
Providing a Frame Sync
(Camera Applications)
The GPI/GPO provides a simple solution for camera
applications that require a frame sync signal from the
ECU (e.g., surround-view systems). Connect the ECU
frame sync signal to the GPI input and connect the GPO
output to the camera frame sync input. GPI/GPO have a
typical delay of 275Fs. Skew between multiple GPI/GPO
channels is maximum 115Fs. If a lower skew signal is
required, connect the camera’s frame sync input to one
of the serializer’s GPIOs and use an I2C broadcast write
command to change the GPIO output state. This has a
maximum skew of 1.5Fs, independent from the used I2C
bit rate.
Software Programming of the
Device Addresses
The serializer and deserializer have programmable device
addresses. This allows multiple GMSL devices, along with
I2C peripherals, to coexist on the same control channel.
The serializer device address is in register 0x00 of each
device, while the deserializer device address is in register
0x01 of each device. To change a device address, first
write to the device whose address changes (register 0x00
of the serializer for serializer device address change, or
register 0x01 of the deserializer for deserializer device
address change). Then write the same address into the
corresponding register on the other device (register 0x00
of the deserializer for serializer device address change,
or register 0x01 of the serializer for deserializer device
address change).
Three-Level Configuration Inputs
CONF1 and CONF0 are three-level inputs that control
the serial interface configuration and power-up defaults.
Connect CONF1or CONF0 through a pullup resistor to
IOVDD to set a high level, a pulldown resistor to GND to
set a low level, or IOVDD/2 or open to set a midlevel. For
digital control, use three-state logic to drive the three-
level logic inputs.
Configuration Blocking
The serializer can block changes to registers. Set
CFGBLOCK to make all registers read only. Once set, the
registers remain blocked until the supplies are removed
or until PWDN is low.
Compatibility with Other GMSL Devices
The MAX9273 serializer is designed to pair with the
MAX9272 deserializer, but interoperates with any GMSL
deserializer. See Table 12 for operating limitations.
GPIOs
The serializer has five open-drain GPIOs available when
not used as data or configuration inputs. Setting the GPIO
enable bits (register 0x0E) to 1 enables the GPIOs and
internally connects the respective data or configuration
input low. Setting the GPIO output bits to 0 pulls the output
low, while setting the bits to 1 leaves the output undriven,
and pulled high through internal/external pullup resistors.
The GPIO input buffers are enabled when the GPIO is
enabled. The input states are stored in register 0x10. Set
GPIO_OUT to 1 when using a GPIO_ as an input.
Table 12. MAx9273 Feature Compatibility
MAx9273 FEATURE
GMSL DESERIALIZER
HSYNC/VSYNC encoding
If feature not supported in deserializer, must be turned off in the serializer.
Hamming-code error
correction
If feature not supported in deserializer, must be turned off in the serializer.
I2C-to-I2C
If feature not supported in deserializer, must use UART-to-I2C or UART-to-UART.
CRC error detection
If feature not supported in deserializer, must be turned off in the serializer.
Double input
If feature not supported in deserializer, data is output as a single word at half the input
frequency.
Coax
If feature not supported in deserializer, must connect unused serial input through 200nF and
50I in series to AVDD and set the reverse control-channel amplitude to 100mV.
I2S encoding
If supported in the deserializer, disable I2S in the deserializer.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9271GTJ/V+T | IC SERIALIZER 16BIT GMSL 32TQFN |
| VI-B3V-CU-S | CONVERTER MOD DC/DC 5.8V 200W |
| MAX9271GTJ+T | IC SERIALIZER 16BIT GMSL 32TQFN |
| VI-B3T-CU-S | CONVERTER MOD DC/DC 6.5V 200W |
| VI-B30-CU-S | CONVERTER MOD DC/DC 5V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9275GTN/V+T | 制造商:Maxim Integrated Products 功能描述:SERIALIZER WITH PARALLEL CMOS INPUTS, NON-HDCP - Tape and Reel |
| MAX9276GTN/V+GG6 | 制造商:Maxim Integrated Products 功能描述:IC DESERIALIZER GMSL 3.12GBPS |
| MAX9276GTN/V+T | 制造商:Maxim Integrated Products 功能描述:3.12GBPS GMSL DESERIALIZERS FOR COAX OR STP INPUTS AND PARAL - Tape and Reel |
| MAX9276GTN+ | 制造商:Maxim Integrated Products 功能描述:DE-SERIALIZER WITH PARALLEL CMOS OUTPUTS, NON-HDCP - Rail/Tube |
| MAX9277GTM/V+GG7 | 制造商:Maxim Integrated Products 功能描述:IC SERIALIZER LVDS |
發布緊急采購，3分鐘左右您將得到回復。