參數資料
型號: MAX79C
廠商: Maxim Integrated Products, Inc.
英文描述: 3.0V/3.3V Adjustable Microprocessor Supervisory Circuits
中文描述: 3.0V/3.3V可調微處理器監控電路
文件頁數: 19/20頁
文件大?。?/td> 150K
代理商: MAX79C
M
3.0V /3.3V Adjustable Mic roproc essor
S upervisory Circ uits
______________________________________________________________________________________
19
___________________Chip Information
_________________Pin Configurations
CE IN
CE OUT
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
BATT
RESET
LOWLINE
RESET
PFI
(RESET IN) BATT OK
V
CC
OUT
TOP VIEW
MAX793
MAX794
CE OUT
CE IN
WDI
WDO
MR
PFO
GND
BATT ON
DIP / Narrow SO
1
2
3
4
8
7
6
5
BATT
GND
BATT ON
V
CC
OUT
MAX795
DIP/SO
RESET
( ) ARE FOR MAX794
TRANSISTOR COUNT: 1271
have without causing a reset pulse to be issued. As
the amplitude of the transient increases (i.e., goes far-
ther below the reset threshold), the maximum allowable
pulse width decreases. Typically, a V
CC
transient that
goes 40mV below the reset threshold and lasts for
10μs or less will not cause a reset pulse to be issued.
A 0.1μF bypass capacitor mounted close to the V
CC
pin provides additional transient immunity.
Watc hdog S oftware Considerations
There is a way to help the watchdog timer monitor soft-
ware execution more closely, which involves setting
and resetting the watchdog input at different points in
the program rather than “pulsing” the watchdog input
high-low-high or low-high-low. This technique avoids a
“stuck” loop, in which the watchdog timer would con-
tinue to be reset within the loop, keeping the watchdog
from timing out. Figure 19 shows an example of a flow
diagram where the I/O driving the watchdog input is
set high at the beginning of the program, set low at the
beginning of every subroutine or loop, then set high
again when the program returns to the beginning. If
the program should “hang” in any subroutine, the prob-
lem would quickly be corrected, since the I/O is contin-
ually set low and the watchdog timer is allowed to time
out, causing a reset or interrupt to be issued.
_Ordering Information (c ontinued)
* The MAX793/MAX795 offer a choice of reset threshold voltage.
Select the letter corresponding to the desired reset threshold volt-
age range (T = 3.00V to 3.15V, S = 2.85V to 3.00V, R = 2.55V
to 2.70V) and insert it into the blank to complete the part number.
The MAX794’s reset threshold is adjustable.
16 Narrow SO
8 Plastic DIP
-40°C to +85°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
MAX794ESE
MAX795
_CPA
16 Plastic DIP
16 Narrow SO
16 Plastic DIP
PIN-PACKAGE
TEMP. RANGE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
MAX794EPE
MAX794CSE
MAX794
CPE
PART*
8 SO
-40°C to +85°C
MAX795_ESA
8 Plastic DIP
8 SO
MAX795_EPA
MAX795_CSA
相關PDF資料
PDF描述
MAX79E 3.0V/3.3V Adjustable Microprocessor Supervisory Circuits
MAX794ESE 3.0V/3.3V Adjustable Microprocessor Supervisory Circuits
MAX794CPE Quadruple 2-Input Exclusive-OR Gates 14-CDIP -55 to 125
MAX794CSE Quadruple 2-Input Exclusive-OR Gates 14-CFP -55 to 125
MAX794EPE 3.0V/3.3V Adjustable Microprocessor Supervisory Circuits
相關代理商/技術參數
參數描述
MAX8 制造商:Lanzar 功能描述:4Ohm 600W Peak 8 Paper Cone Woofer 制造商:LANZAR 功能描述:8 PAPER CONE WOOFER 4OHM 600W PEAK
MAX-80 功能描述:保險絲 32V 80A Blade Clear RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485
MAX800 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Microprocessor Supervisory Circuits
MAX800L 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Microprocessor Supervisory Circuits
MAX800LCPE 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel