參數資料
型號： MAX5960AECS+T
廠商： Maxim Integrated
文件頁數： 12/25頁
文件大?。?/td> 632K
描述： IC CTRLR HOT-PLUG QD 80-TQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1,000
類型： 熱交換控制器
應用： 通用型，PCI Express?
內部開關： 無
電源電壓： 3.3V，12V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 80-TQFP
供應商設備封裝： 80-TQFP（12x12）
包裝： 帶卷 (TR)
Quad PCI Express, Hot-Plug Controllers
12   ______________________________________________________________________________________
Pin Description (continued)
PIN
NAME
FUNCTION
23
3.3SC-
Slot C 3.3V Negative Current-Sense Input. Connect to the negative side of the sense resistor using the
Kelvin-sensing technique to ensure accurate current sensing.
24
3.3GC
Slot C 3.3V Gate-Drive Output. Connect 3.3GC to the gate of slot Cs 3.3V MOSFET. At power-up,
3.3GC is charged to 5.5V above the 3.3V supply by a constant current derived from V
12VIN
. V
3.3GC
s
rise time is determined by the external gate capacitance.
25
FAULTC
Open-Drain Fault Output Signal. FAULTC latches active-low whenever slot C outputs are shut down due
to a fault. A fault is either of:
" An overcurrent condition lasting longer than the overcurrent timeout.
" A device over temperature condition.
If the fault is detected in the main outputs, FAULTC must be reset by toggling the ONC input. If the fault
is in the auxiliary output, FAULTC must be reset by toggling both ONC and AUXONC. For the
autorestart version, FAULTC is reset when the part initiates the next power-on cycle.
26
PWRGDC
Open-Drain Power-Good Output. PWRGDC goes low 160ms
 
after all outputs of slot C reach their final
value and the power MOSFETs are fully enhanced.
27,28
3.3AUXOC    Slot C 3.3V Auxiliary Power-Supply Output
29, 30, 31,
69, 70, 71
3.3VAUXIN
3.3V Auxiliary Supply Input. 3.3VAUXIN is the input to a charge pump that drives the internal MOSFETs
connecting 3.3AUXIN to 3.3AUXO_. V
3.3AUXIN
is also used to power the internal control logic and
analog references of the MAX5959/MAX5960 and must always be connected to a supply between 3V
and 3.6V. Bypass 3.3AUXIN with at least a 0.1礔 capacitor to GND.
32, 33
3.3AUXOD    Slot D 3.3V Auxiliary Power-Supply Output
34, 66
PGND
Power Ground. Connect externally to GND.
35
PWRGDD
Open-Drain Power-Good Output. PWRGDD goes low 160ms
 
after all outputs of slot D reach their final
value and the power MOSFETs are fully enhanced.
36
FAULTD
Open-Drain Fault Output Signal. FAULTD latches active-low whenever slot D outputs are shut down due
to a fault. A fault is either of:
" An overcurrent condition lasting longer than the overcurrent timeout.
" A device over temperature condition.
If the fault is detected in the main outputs, FAULTD must be reset by toggling the OND input. If the fault
is in the auxiliary output, FAULTD must be reset by toggling both OND and AUXOND. For the
autorestart version, FAULTD is reset when the part initiates the next power-on cycle.
37
TIM
Overcurrent Timeout Programming Input. Connect a resistor between 500?and 500k?from TIM to
GND to program t
FAULT
. Leave TIM unconnected for a default timeout of 11ms.
38
PORADJ
Power-On-Reset Programming Input. Connect a resistor between 500?and 500k?from PORADJ to
GND to program the POR timing. Leave unconnected for a default value of 160ms. Connect PORADJ to
GND to completely skip the POR time delay for PWRGD_ assertion.
39
GND
Ground
40
12VIN
12V Supply Input. V
12VIN
 drives the gates of the MOSFETs connected to 3.3G_. 12VIN powers an
internal charge pump that drives the gates of the MOSFETs connected to 12G_. Bypass 12VIN with a
1礔 capacitor to GND. See the Typical Application Circuit and Input Transients section.
41
12GD
Slot D 12V Gate-Drive Output. Connect 12GD to the gate of slot Ds 12V MOSFET. At power-up, V
12GD
is raised to the internal charge-pump voltage level by a constant current.
42
12SD-
Slot D 12V Negative Current-Sense Input. Connect 12SD- to the negative side of the current-sense
resistor using the Kelvin-sensing technique to ensure accurate current sensing.
相關PDF資料
PDF描述
MAX5963UTL+T IC HOT SWAP DIO ORING CTL 40TQFN
MAX5965AEAX+ IC PSE CTRLR FOR POE 36SSOP
MAX5969DETE+T IC CTRLR INTERFCE W/MOSFT 16TQFN
MAX5971AETI+ IC CTRLR PD IEEE 802.3AF 28WQFN
MAX5972AETE+T IC CONTROLLER INTERFACE 16TQFN
相關代理商/技術參數
參數描述
MAX5960LECS+ 功能描述:熱插拔功率分布 Triple PCIe Hot Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5960LECS+T 功能描述:熱插拔功率分布 Triple PCIe Hot Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5960LEVCMAXQU+ 功能描述:熱插拔功率分布 MAX5959A/L/60A/L Eval System RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5960LEVKIT+ 功能描述:熱插拔功率分布 MAX5959A/L/60A/L Eval System RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5961ETM+ 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*