- 您現在的位置：買賣IC網 > PDF目錄385532 > MAX5003CSE (MAXIM INTEGRATED PRODUCTS INC) High-Voltage PWM Power-Supply Controller PDF資料下載
參數資料
| 型號： | MAX5003CSE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | High-Voltage PWM Power-Supply Controller |
| 中文描述： | 1 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SO-16 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 170K |
| 代理商： | MAX5003CSE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
V
CC
regulator has a lockout line that shorts the N-chan-
nel MOSFET driver output to ground if the V
CC
LDO is
not regulating. V
CC
feeds all circuits except the V
CC
lockout logic, the undervoltage lockout, and the power
regulators.
The preferred method for powering the MAX5003 is to
start with the high-voltage power source (at V+ or ES,
depending on the application), then use a bootstrap
source from the same converter with an output voltage
higher than the V
DD
regulator turn-off voltage (10.75V)
to power V
DD
. This will disable the power consumption
of the V
DD
LDO. It is also possible to power the
MAX5003 with no bootstrap source from ES or V+, but
do not exceed the maximum allowable power dissipa-
tion. The current consumption of the part is mostly a
function of the operating frequency and the type of
external power switch used—in particular, the total
charge to be supplied to the gate.
A reference output of 3V nominal is externally available
at the REF pin, with a current sourcing capability of
1mA. A lockout circuit shuts off the oscillator and the
output driver if REF falls 200mV below its set value.
Minimize loading at REF, since the REF voltage is the
source for the FB voltage, which is the regulator set
point when the error amplifier is used. Any changes in
V
REF
will be proportionally reflected in the regulated
output voltage of the converter.
Undervoltage Lockout, Feed Forward,
and Shutdown
The undervoltage lockout feature disables the controller
when the voltage at INDIV is below 1.2V (120mV hys-
teresis). When INDIV rises higher than 1.2V plus the
hysteresis (typically 1.32V), it allows the controller to
start. An external resistive divider connected between
the power line and AGND generates the INDIV signal.
INDIV is also used as the signal for the fast input volt-
age feed-forward circuit.
Always connect INDIV to a voltage divider. It is not a
“don’t care” condition; the signal is used to set the fast
feed-forward circuit (see the
Oscillator and Ramp
Generator
section).
Choose R2 (Figure 2) between 25k
to 500k
and cal-
culate R1 to satisfy the following equation:
where V
SUL
= system undervoltage lockout and
V
INDIVLO
= I
NDIV
undervoltage lockout.
The undervoltage lockout function allows the use of the
INDIV pin as a shutdown pin with an external switch to
ground. The shutdown circuit must not affect the resis-
tive divider during normal operation.
Current-Sense Comparator
The current-sense (CS) comparator and its associated
logic limit the current through the power switch. Current
is sensed at CS as a voltage across a sense resistor
between the external MOSFET source and PGND.
Connect CS to the external MOSFET source through a
100
resistor or RC lowpass filter (Figures 2 and 3).
See
CS Resistor
in the
Component Selection
section.
A blanking circuit shunts CS to ground when the power
MOSFET switch is turned off, and keeps it there for
70ns after turn-on. This avoids false trips caused by the
switching transients. The blanking circuit also resets
the RC filter, if used. When V
CS
> 100mV, the power
MOSFET is switched off. The propagation delay from
the time the switch current reaches the trip level to the
driver turn-off time is 240ns. If the current limit is not
used, the CS pin must be connected to PGND.
Error Amplifier
The internal error amplifier is one of the building blocks
that gives the MAX5003 its flexibility. Its noninverting
input is biased at 1.5V, derived from the internal 3V ref-
erence. The inverting input is brought outside (FB pin)
and is the regulation feedback connection point. If the
error amplifier is not used, connect this pin to ground.
The output is available for the frequency compensation
network and for connection to the input of the PWM
comparator (CON). Unity-gain frequency is 1.2MHz,
open-circuit gain is 80dB, and the amplifier is unity-
gain stable. To eliminate long overload recovery times,
there are clamps limiting the output excursions close to
the range limits of the PWM ramp. The voltage at the
noninverting input of the error amplifier is the regulator
set point, but is not accessible.
Set-point voltage can be measured, if needed, by con-
necting COMP and FB and measuring that node with
respect to ground. The error amplifier is powered from
the V
CC
rail.
PWM Comparator
The pulse-width modulator (PWM) comparator stage
transforms the error signal into a duty cycle by comparing
the error signal with a linear ramp. The ramp levels are
0.5V min and 2.5V max. The comparator has a typical
hysteresis of 5.6mV and a propagation delay of 100ns.
The output of the comparator controls the external FET.
Soft-Start
The soft-start feature allows converters built using the
MAX5003 to apply power to the load in a controllable
soft ramp, thus reducing start-up surges and stresses.
R
R
V
V
SUL
INDIVLO
1
2
1
=
M
High-Voltage PWM
Power-Supply Controller
_______________________________________________________________________________________
9
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5003EEE | High-Voltage PWM Power-Supply Controller |
| MAX5003ESE | RES 240-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA |
| MAX500 | CMOS, Quad, Serial-Interface 8-Bit DAC(電壓輸出,四通道,串行,8位D/A轉換器) |
| MAX5024 | 65V, Low-Quiescent-Current, High-Voltage Linear Regulators with レP Reset and Watchdog Timer |
| MAX5023-MAX5024 | 65V, Low-Quiescent-Current, High-Voltage Linear Regulators with レP Reset and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5003CSE+ | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003CSE+T | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003CSE-T | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003EEE | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003EEE+ | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。