- 您現在的位置：買賣IC網 > PDF目錄385532 > MAX5003CSE (MAXIM INTEGRATED PRODUCTS INC) High-Voltage PWM Power-Supply Controller PDF資料下載
參數資料
| 型號： | MAX5003CSE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | High-Voltage PWM Power-Supply Controller |
| 中文描述： | 1 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SO-16 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 170K |
| 代理商： | MAX5003CSE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
M
It also determines power-up sequencing when several
converters are used.
Upon power turn-on, the SS pin acts as a current sink
to reset any capacitance attached to it. Once REF has
exceeded its lockout value, SS sources a current to the
external capacitor, allowing the converter output volt-
age to ramp up. Full output voltage is reached in
approximately 0.45s/μF.
The SS pin is an overriding extra input to the PWM
comparator. As long as its voltage is lower than V
CON
,
it overrides V
CON
and SS determines the level at which
the duty cycle is decided by the PWM comparator.
After exceeding V
CON
, SS no longer controls the duty
cycle. Its voltage will keep rising up to V
CC
.
Oscillator and Ramp Generator
The MAX5003 oscillator generates the ramp used by
the comparator, which in turn generates the PWM digi-
tal signal. It also controls the maximum on-time feature
of the controller. The oscillator can operate in two
modes: free running and synchronized (sync). A single
pin, FREQ, doubles as the attachment point for the fre-
quency programming resistor and as the synchroniza-
tion input. The mode recognition is automatic, based on
the voltage level at the FREQ pin.
In free-running mode, a 1.25V source is internally
applied to the pin; the oscillator frequency is propor-
tional to the current out of the pin through the program-
ming resistor, with a proportionality constant of
16kHz/μA.
In sync mode, the signal from the external master gen-
erator must be a digital rectangular waveform running
at four times the desired converter switching frequency.
Minimum acceptable signal pulse width is 150ns, posi-
tive or negative, and the maximum frequency is
1.2MHz.
When the voltage at FREQ is forced above 2.7V, the
oscillator goes into sync mode. If left at or below 1.5V for
more than 8μs to 20μs, it enters free-running mode.
The master clock generator cannot be allowed to stop
at logic zero. If the system design forces such a situa-
tion, an inverter must be used at the FREQ pin.
In sync mode, the oscillator signal is divided by four and
decoded. The output driver is blocked during the last
phase of the division cycle, giving a hardwired maximum
on-time of 75%. In free-running mode, the oscillator duty
cycle is 75% on, and the off portion also blocks the out-
put driver. The maximum on-time is then absolutely limit-
ed to 75% in either mode. Maximum on-time can be
controlled to values lower than 75% by a programming
resistor at the MAXTON pin.
The PWM ramp generated goes from 0.5V min to 2.5V
max, and the maximum time on is the time it takes from
low to high.
MAXTON is internally driven to V
INDIV
and a resistor
must be connected from MAXTON to AGND, to pro-
gram the maximum on-time.
The ramp slope is directly proportional to V
INDIV
and
inversely proportional to R
MAXTON
. Since the ramp volt-
age limits are fixed, controlling the ramp slope sets the
maximum time on.
Changing the ramp slope while V
CON
remains constant
also changes the duty cycle and the energy transferred to
the load per cycle of the converter. The INDIV signal is a
fraction of the input voltage, so the fast input voltage feed-
forward works by modifying the duty cycle in the same
clock period, in response to an input voltage change.
Calculate the maximum duty cycle as:
where:
D
MAX
= Maximum duty cycle (%)
MAXTON = Maximum on-time
T = Switching period
Then:
where:
R
MAXTON
= Resistor from the MAXTON pin to ground
V
INDIV
= Voltage at the INDIV pin
SW
= Output switching frequency
MAXTON can then be calculated as:
N-Channel MOSFET
Output Switch Driver
The MAX5003 output drives an N-channel MOSFET
transistor. The output sources and sinks relatively large
currents, supplying the gate with the charge the tran-
sistor needs to switch. These are current spikes only,
since after the switching transient is completed the load
is a high-value resistance. The current is supplied from
the V
CC
rail and must be sourced by a large-value
MAXTON
R
V
k
V
kHz
MAXTON
INDIV
=
0 75
200
1 25
100
.
.
D
0.75 100 R
200k
1.25V
V
INDIV
100kHz
MAX
MAXTON
SW
=
D
MAXTON
T
MAX
=
100
High-Voltage PWM
Power-Supply Controller
10
______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5003EEE | High-Voltage PWM Power-Supply Controller |
| MAX5003ESE | RES 240-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA |
| MAX500 | CMOS, Quad, Serial-Interface 8-Bit DAC(電壓輸出,四通道,串行,8位D/A轉換器) |
| MAX5024 | 65V, Low-Quiescent-Current, High-Voltage Linear Regulators with レP Reset and Watchdog Timer |
| MAX5023-MAX5024 | 65V, Low-Quiescent-Current, High-Voltage Linear Regulators with レP Reset and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5003CSE+ | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003CSE+T | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003CSE-T | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003EEE | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX5003EEE+ | 功能描述:電壓模式 PWM 控制器 PWM Power-Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。