M
Complete DBS Direct-Conversion Tuner ICs
with Monolithic VCOs
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
V
CC
to GND...........................................................-0.3V to +5.5V
All Other Pins to GND.................................-0.3V to (V
CC
+ 0.3V)
RFIN+ to RFIN-, XTL+ to XTL-, IDC+ to IDC-,
QDC+ to QDC- ...................................................................±2.0V
CNTOUT, XTALOUT, CPOUT, VREG1/2,
I/QOUT± to GND Short-Circuit Duration.................................10s
Continuous Current (any pin other than V
CC
or GND) .......10mA
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Continuous Power Dissipation (T
A
= +85°C)
40-Pin Thin QFN (derate 23.3mW/°C above +85°C) .... 1.86W
Operating Temperature Range ..............................0°C to +85°C
Junction Temperature .....................................................+150°C
Storage Temperature Range ............................-65°C to +160°C
Soldering Temperature (10s) ..........................................+300°C
DC ELECTRICAL CHARACTERISTICS
(V
CC
= +4.75V to +5.25V, GND = 0V, GC1 = +0.75V; no AC signal applied, default register settings, T
A
= 0°C to +85°C, unless other-
wise noted. Typical values are at V
CC
= +5V, T
A
= +25°C, unless otherwise noted.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
SUPPLY
Supply Voltage
Supply Current
ANALOG GAIN CONTROL INPUT
—
GC1
Usable Voltage Range
Input Current
BASEBAND OUTPUTS
—
IOUT, QOUT (MAX2116)
Nominal Output Voltage Swing
Output Clipping Voltage
DC Output Voltage
BASEBAND OUTPUTS
—
IOUT±, QOUT± (MAX2118)
4.75
5.25
265
V
LO locked at 2175MHz
195
mA
0.75
-50
2.6
+50
V
μA
0.75V < GC1 < 2.6V (Note 2)
R
LOAD
= 1k
// 10pF (Note 3)
0.8
2
1.2
V
P-P
V
P-P
V
Bit DL = high
Bit DL = low
1
Nominal Output Voltage Swing
R
LOAD
= 2k
// 10pF
(differential) (Note 3)
0.59
2
0.75
0
V
P-P
Output Clipping Voltage
Common-Mode Voltage
DC Offset Voltage
ANALOG OUTPUT
—
VREG1, VREG2
Output Voltage
Source Current
STATIC CONTROL INPUTS
—
AS2, AS1, AS0
Input Voltage High
Input Voltage Low
Input Current
SYNTHESIZER DC PARAMETERS
V
P-P
V
mV
0.65
-50
0.85
+50
2.7
2.85
3.05
3
V
Each output
mA
4
V
V
μA
0.5
+50
-50
Bits CP1 = 0, CP0 = 0
Bits CP1 = 0, CP0 = 1
Bits CP1 = 1, CP0 = 0
Bits CP1 = 1, CP0 = 1
±
35
±
70
±
140
±
280
±
50
±
100
±
200
±
400
±
68
±
136
±
272
±
544
Charge Pump Source/Sink Current
μA