- 您現在的位置：買賣IC網 > PDF目錄383345 > MAX2116EVKIT (Maxim Integrated Products, Inc.) MAX2116/MAX2118 Evaluation Kits PDF資料下載
參數資料
| 型號： | MAX2116EVKIT |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | MAX2116/MAX2118 Evaluation Kits |
| 中文描述： | MAX2116、MAX2118評估板 |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 314K |
| 代理商： | MAX2116EVKIT |
BYTE 05 (default = 1F)
Bits D(2), D(1), and D(0) control diagnostic features
(Table 7).
Bits G(4)
–
G(0) controls the gain of the baseband VGA.
The BB gain is minimum at 11111 and the BB gain is
maximum at 00000. Default is minimum gain setting of
11111 (Table 8).
I
2
C Read Status Bits
Bit PWR high indicates power has been cycled, and the
MAX2116/MAX2118 registers have been reset to
default values. A stop condition while in read mode
resets this bit.
Bits ADC(2), ADC(1), and ADC(0) represent a 3-bit
ADC conversion of the VCO tune voltage used for VCO
and charge pump current selection and calibration.
Bits F(6)
–
F(0) are a 7-bit representation of the LPF DAC
current.
Serial Interface Functional Description
Register Map
This is the standard I
2
C protocol. The write/read/
address bytes are dependent on the states of pins
AS0/AS1/AS2.
Write Operation
The first byte is the device address plus the direction
bit (R/
W
= 0).
The second byte contains the internal address com-
mand of the first address to be accessed.
The third byte is written to the internal register directed
by the command address byte.
The following bytes (if any) are written into successive
internal registers.
The transfer lasts until stop conditions are encountered.
The MAX2116 acknowledges every byte transfer.
Read Operation
When an address is sent, the MAX2116 sends back
first the status byte and then the I/Q DAC byte.
Example:
Write registers 0 to 3 with 0E, D8, 26 (Table 9).
Example:
Read from status registers. Sending an ACK
terminates slave transmit mode (Table 10).
M
Complete DBS Direct-Conversion Tuner ICs
with Monolithic VCOs
______________________________________________________________________________________
13
CP1
0
0
1
1
CP0
0
1
0
1
CHARGE PUMP CURRENT (μA)
±
50
±
100
±
200
±
400 (default)
Table 4. Charge Pump Current Setting
(Byte 02)
OSC2
OSC1
OSC0
VCO
BAND
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5 (Default)
6
7
Table 5. On-Chip VCO Selection (Byte 02)
DL
IOUT±, QOUT± OUTPUT VOLTAGE LEVEL
(DIFFERENTIAL) (V
P-P
)
0.59
1.0
0
1
Table 6. MAX2118 Output Drive Level
Selection (Byte 04)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2116 | 16-Bit Buffers/Drivers With 3-State Outputs 48-SSOP -40 to 85 |
| MAX2116UTL | Complete DBS Direct-Conversion Tuner ICs with Monolithic VCOs |
| MAX2118EVKIT | MAX2116 Evaluation Kits |
| MAX2118UTL | Complete DBS Direct-Conversion Tuner ICs with Monolithic VCOs |
| MAX2120 | Complete, Direct-Conversion Tuner for DVB-S and Free-to-Air Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2116EVKIT+ | 功能描述:射頻開發工具 MAX2116 Eval Kit RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| MAX2116UGL | 功能描述:調諧器 RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| MAX2116UGL-T | 功能描述:調諧器 RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| MAX2116UTL | 功能描述:調諧器 RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| MAX2116UTL+ | 功能描述:調諧器 Direct Conv Tuner w/Monolithic VCO RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。