- 您現在的位置：買賣IC網 > PDF目錄383345 > MAX2055EUP (Maxim Integrated Products, Inc.) RELIABILITY REPORT FOR MAX2055EUP PLASTIC ENCAPSULATED DEVICES PDF資料下載
參數資料
| 型號： | MAX2055EUP |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | RELIABILITY REPORT FOR MAX2055EUP PLASTIC ENCAPSULATED DEVICES |
| 中文描述： | 可靠性報告的MAX2055EUP塑封器件 |
| 文件頁數： | 11/13頁 |
| 文件大小： | 805K |
| 代理商： | MAX2055EUP |
feedback topology. This amplifier is optimized for a fre-
quency range of operation from 30MHz to 300MHz with
a high-output third-order intercept point (OIP3). The
bias current is chosen to optimize the IP3 of the amplifi-
er. When R
1
is 1.13k
(909
if using the circuit of
Figure 2), the current consumption is 240mA while
exhibiting a 40dBm typical output IP3 at 70MHz. The
common-mode inductor, L
2
, provides a high common-
mode rejection with excellent amplitude and phase bal-
ance at the output. L
2
must handle the supply current
and have DC resistance less than 0.2
.
Choke Inductor
The single-ended amplifier input and differential output
ports require external choke inductors. At the input,
connect a 330nH bias inductor from AMP
IN
(pin 15) to
I
BIAS
(pin 12). Connect 680nH choke inductors from
RF_OUT+ (pin 11) and RF_OUT- (pin 10) to V
CC
. These
connections provide bias current to the amplifier.
Layout Considerations
A properly designed PC board is an essential part of
any RF/microwave circuit. Keep RF signal lines as short
as possible to reduce losses, radiation, and induc-
tance. For best performance, route the ground-pin
traces directly to the exposed pad underneath the
M
Digitally Controlled, Variable-Gain, Differential
ADC Driver/Amplifier
______________________________________________________________________________________
11
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
ATTN
OUT
I
SET
R
1
B4
1
RF_IN
V
CC
AMP
IN
C
BP
B0
B1
B2
B3
12
11
9
10
I
BIAS
RF_OUT+
RF_OUT
RF_OUT-
CONTROL
INPUTS
ATTENUATION
LOGIC
CONTROL
V
CC
MAX2055
C
12
C
11
T
2
C
10
V
CC
C
9
L
5
L
4
C
8
C
7
C
5
C
4
C
3
C
1
C
2
L
1
L
2
L
V
CC
RF_IN
GND
V
CC
R
7
GND
GND
C
C
L
E
Figure 2. Low-Cost Application Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2055EUP-T | Digitally Controlled, Variable-Gain, Differential ADC Driver/Amplifier |
| MAX2056 | 800MHz to 1000MHz Variable-Gain Amplifier with Analog Gain Control |
| MAX2056ETX-T | 800MHz to 1000MHz Variable-Gain Amplifier with Analog Gain Control |
| MAX2056ETX | 800MHz to 1000MHz Variable-Gain Amplifier with Analog Gain Control |
| MAX2112 | Complete, Direct-Conversion Tuner for DVB-S2 Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2055EUP+ | 制造商:Maxim Integrated Products 功能描述:ADC DRVR/AMP 20TSSOP EP - Rail/Tube |
| MAX2055EUP+D | 功能描述:射頻混合器 Variable-Gain Diff ADC Driver/Amp RoHS:否 制造商:NXP Semiconductors 頻率范圍: 轉換損失——最大: 工作電源電壓:6 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MAX2055EUP+T | 制造商:Maxim Integrated Products 功能描述:ADC DRVR/AMP 20TSSOP EP - Tape and Reel |
| MAX2055EUP+TD | 功能描述:射頻混合器 Variable-Gain Diff ADC Driver/Amp RoHS:否 制造商:NXP Semiconductors 頻率范圍: 轉換損失——最大: 工作電源電壓:6 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MAX2055EUP-D | 功能描述:射頻放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。