- 您現在的位置：買賣IC網 > PDF目錄2009 > MAX19711ETN+T (Maxim Integrated Products)IC ANLG FRNT END 56-TQFN PDF資料下載
參數資料
| 型號： | MAX19711ETN+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ANLG FRNT END 56-TQFN |
| 產品變化通告： | Product Discontinuation 09/Jun/2011 |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 通道數： | 2 |
| 功率（瓦特）： | 37.5mW |
| 電壓 - 電源，模擬： | 3V |
| 電壓 - 電源，數字： | 3V |
| 封裝/外殼： | 56-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 56-TQFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MAX19711
10-Bit, 11Msps, Full-Duplex
Analog Front-End
______________________________________________________________________________________
19
Tx DAC Timing
Figure 6 shows the relationship among the clock, input
data, and analog outputs. Channel ID data is latched on
the falling edge of the clock signal, and channel QD data
is latched on the rising edge of the clock signal, at which
point both ID and QD outputs are simultaneously updated.
3-Wire Serial Interface and
Operation Modes
The 3-wire serial interface controls the MAX19711 oper-
ation modes as well as the three 12-bit aux-DACs and
the 10-bit aux-ADC. Upon power-up, program the
MAX19711 to operate in the desired mode. Use the 3-
wire serial interface to program the device for shutdown,
idle, standby, FD, Rx, Tx, aux-DAC controls, or aux-ADC
conversion. A 16-bit data register sets the mode control
as shown in Table 3. The 16-bit word is composed of
four control bits (A3–A0) and 12 data bits (D11–D0).
Data is shifted in MSB first (D11) and LSB last (A0) for-
mat. Table 4 shows the MAX19711 power-management
modes. Table 5 shows the SPI-controlled Tx, Rx, and FD
modes. The serial interface remains active in all modes.
SPI Register Description
Program the control bits, A3–A0, in the register as shown
in Table 3 to select the operating mode. Modify A3–A0 bits
to select from ENABLE-16, Aux-DAC1, Aux-DAC2, Aux-
DAC3, IOFFSET, QOFFSET, COMSEL, Aux-ADC,
ENABLE-8, and WAKEUP-SEL modes. ENABLE-16 is the
default operating mode (see Table 6). This mode allows for
shutdown, idle, and standby states as well as switching
between FAST, SLOW, Rx and Tx modes. Tables 4 and 5
show the required SPI settings for each mode.
In ENABLE-16 mode, the aux-DACs have independent
control bits E4, E5, and E6, bit E7 sets the Tx path full-
scale outputs, and bit E9 enables the aux-ADC. Table 7
shows the auxiliary DAC enable codes. Table 8 shows
the full-scale output selection. Table 9 shows the auxil-
iary ADC enable code. Bits E11 and E10 are reserved.
Program bits E11 and E10 to logic-low. Bits E3 and E8
are not used.
Modes Aux-DAC1, Aux-DAC2, and Aux-DAC3 select
the aux-DAC channels named DAC1, DAC2, and DAC3
and hold the data inputs for each DAC. Bits _D11–_D0
are the data inputs for each aux-DAC and can be pro-
grammed through SPI. The MAX19711 also includes
two 6-bit registers that can be programmed to adjust the
offsets for the Tx path ID and QD channels indepen-
dently (see Table 10). Use the COMSEL mode to select
the output common-mode voltage with bits CM1 and
CM0 (see Table 11). Use Aux-ADC mode to start the
auxiliary ADC conversion (see the 10-Bit, 333ksps
Auxiliary ADC section for details). Use ENABLE-8 mode
for faster enable and switching between shutdown, idle,
and standby states as well as switching between FAST,
SLOW, Rx and Tx modes and the FD mode.
The WAKEUP-SEL register selects the operating mode
that the MAX19711 is to enter immediately after coming
out of shutdown (Table 12). See the Wake-Up Function
section for more information.
0.63
CHANNEL EDGE
4.285
fIMAGE
1.3
fC
4.915
fCLK
FREQ (MHz)
NOT TO SCALE
-49.3dB
-15dB
-3dB
0dB
-56dB (min)
-57.1dB
OCCUPIED
CHANNEL
AMPLITUDE
CDMA
FILTER RESPONSE
DAC sin(x)/x
RESPONSE
Tx PATH:
SFDR = 75dBc
THD = -75dBc
SNR = 55.9dB
Figure 4. TD-SCDMA Filter Frequency Response
相關PDF資料 |
PDF描述 |
|---|---|
| MAX19712ETN+T | IC ANLG FRNT END 56-TQFN |
| MAX19713ETN+T | IC ANLG FRNT END 56-TQFN |
| MAX271ENG+ | IC FILTER LOWPASS PROG 24-DIP |
| MAX274ACWI+T | IC FILTER ANALOG 8TH-ORD 28SOIC |
| MAX281AEWE+ | IC FILTER 5TH-ORD BESSEL 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX19711EVCMODU+ | 功能描述:數據轉換 IC 開發工具 MAX19710/13 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX19711EVKIT | 功能描述:數據轉換 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX19711EVKIT+ | 功能描述:數據轉換 IC 開發工具 MAX19710/13 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX19712ETN | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19712ETN+ | 功能描述:ADC / DAC多通道 22Msps CODEC/AFE Full Duplex RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
發布緊急采購，3分鐘左右您將得到回復。