- 您現在的位置：買賣IC網 > PDF目錄383334 > MAX1777EEI (MAXIM INTEGRATED PRODUCTS INC) 32-Bit Digital Signal Controller with ROM 100-BGA MICROSTAR -40 to 125 PDF資料下載
參數資料
| 型號： | MAX1777EEI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 32-Bit Digital Signal Controller with ROM 100-BGA MICROSTAR -40 to 125 |
| 中文描述： | DUAL SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-28 |
| 文件頁數： | 19/32頁 |
| 文件大小： | 497K |
| 代理商： | MAX1777EEI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
High-Effic ienc y, Quad Output, Main Power-
S upply Controllers for Notebook Computers
______________________________________________________________________________________
19
tinuous and discontinuous inductor-current operation
(also known as the critical conduction point):
where K is the on-time scale factor (see the
On-Time
One-Shot (t
ON
)
section). The load-current level at which
PFM/PWM crossover occurs, I
LOAD(SKIP)
, is equal to 1/2
the peak-to-peak ripple current, which is a function of the
inductor value (Figure 5). For example, in the MAX1777
typical application circuit with V
OUT2
= 5V, V+ = 12V,
L = 7.6μH, and K = 5μs, switchover to pulse-skipping
operation occurs at I
LOAD
= 0.96A or about 1/5 full load.
The crossover point occurs at an even lower value if a
swinging (soft-saturation) inductor is used.
The switching waveforms may appear noisy and asyn-
chronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
results in high light-load efficiency. Trade-offs in PFM
noise vs. light-load efficiency are made by varying the
inductor value. Generally, low inductor values produce
a broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the
coil resistance remains fixed) and less output voltage
ripple. Penalties for using higher inductor values
include larger physical size and degraded load-tran-
sient response (especially at low input voltage levels).
DC output accuracy specifications refer to the trip level of
the error comparator. When the inductor is in continuous
conduction, the output voltage has a DC regulation high-
er than the trip level by 50% of the ripple. In discontinu-
ous conduction (
SKIP
= GND, light load), the output
voltage has a DC regulation higher than the trip level by
approximately 1.5% due to slope compensation.
Forc ed-PWM Mode
The low-noise, forced-PWM (
SKIP
= V
CC
) mode dis-
ables the zero-crossing comparator, which controls the
low-side switch on-time. Disabling the zero-crossing
detector causes the low-side, gate-drive waveform to
become the complement of the high-side, gate-drive
waveform. The inductor current reverses at light loads
as the PWM loop strives to maintain a duty ratio of
V
OUT
/V+. The benefit of forced-PWM mode is to keep
the switching frequency fairly constant, but it comes at
a cost: the no-load battery current can be 10mA to
50mA, depending on switching frequency and the
external MOSFETs.
Forced-PWM mode is most useful for reducing audio-
frequency noise, improving load-transient response,
providing sink-current capability for dynamic output
voltage adjustment, and improving the cross-regulation
of multiple-output applications that use a flyback trans-
former or coupled inductor.
Minimum 25kHz Pulse-S kipping Mode
(Ultrasonic Mode)
Leaving
SKIP
unconnected or connecting
SKIP
to REF
activates a pulse-skipping mode with a minimum
switching frequency of 25kHz. This ultrasonic pulse-
skipping mode reduces audio-frequency modulation of
the power supply that may occur in Idle Mode at very
light loads. The transition to fixed-frequency PWM oper-
ation is automatic and occurs at the same point as in
Idle Mode. Ultrasonic pulse skipping occurs if no
switching has taken place within the last 28μs. DL_
turns on to induce a regulated negative current in the
inductor. DH_ turns on when the inductor current
reaches the regulated negative current limit. Starting
with a DL_ pulse greatly reduces the ripple current
when compared to starting with a DH_ pulse (Idle
Mode). The output voltage level determines the nega-
tive current limit.
Calculate the negative ultrasonic current-limit threshold
with the following equation:
where V
FB
> V
REF
, and R
ON
is the on-resistance of the
synchronous rectifier (MAX1999) or the current-sense
resistor value (MAX1777/MAX1977).
V
I
R
V
V
V
V
NEG
LX
ON
REF
FB
ILIM
S
U
=
×
=
×
(
)
.
_
0 467
I
K
V
2
L
V
V
+
V
LOAD SKIP
OUT
×
OUT
(
)
_
_
=
×
+
I
I
LOAD
= I
PEAK
/2
ON-TIME
0
TIME
-I
PEAK
L
V+
- V
OUT
i
t
=
Figure 5. Pulse- Skipping/Discontinuous Crossover Point
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1777 | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1777-MAX1999 | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1977 | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1999 | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1977EEI | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1777EEI+ | 功能描述:DC/DC 開關控制器 Quad-Out Main Power Sply Ctlr for Ntbk RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1777EEI+T | 功能描述:DC/DC 開關控制器 Quad-Out Main Power Sply Ctlr for Ntbk RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1777EEI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1778EUG | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1778EUG+ | 功能描述:直流/直流開關轉換器 Quad-Output TFT LCD w/Buffer RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。