- 您現在的位置：買賣IC網 > PDF目錄383331 > MAX1668 (Maxim Integrated Products, Inc.) Multichannel Remote/Local Temperature Sensors PDF資料下載
參數資料
| 型號： | MAX1668 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Multichannel Remote/Local Temperature Sensors |
| 中文描述： | 多通道遠端/本地溫度傳感器 |
| 文件頁數： | 11/17頁 |
| 文件大小： | 285K |
| 代理商： | MAX1668 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Diode Fault Alarm
There is a continuity fault detector at DXP_ that detects
whether the remote diode has an open-circuit condi-
tion. At the beginning of each conversion, the diode
fault is checked, and the status byte is updated. This
fault detector is a simple voltage detector; if DXP_ rises
above V
CC
- 1V (typ) due to the diode current source, a
fault is detected. Note that the diode fault is not
checked until a conversion is initiated, so immediately
after power-on reset, the status byte indicates no fault
is present, even if the diode path is broken.
If any remote channel is shorted (DXP_ to DXN_ or
DXP_ to GND), the ADC reads 0000 0000 so as not to
trip either the T
HIGH
or T
LOW
alarms at their POR set-
tings. In applications that are never subjected to 0°C in
normal operation, a 0000 0000 result can be checked
to indicate a fault condition in which DXP_ is acciden-
tally short circuited. Similarly, if DXP_ is short circuited
to V
CC
, the ADC reads +127°C for all remote and local
channels, and the device alarms.
ALERT
Interrupts
The
ALERT
interrupt output signal is latched and can
only be cleared by reading the alert response address.
Interrupts are generated in response to T
HIGH
and T
LOW
comparisons and when a remote diode is disconnected
(for continuity fault detection). The interrupt does not halt
automatic conversions; new temperature data continues
to be available over the SMBus interface after
ALERT
is
asserted. The interrupt output pin is open drain so that
devices can share a common interrupt line. The interrupt
rate can never exceed the conversion rate.
The interface responds to the SMBus alert response
address, an interrupt pointer return-address feature
(see
Alert Response Address
section). Prior to taking
corrective action, always check to ensure that an inter-
rupt is valid by reading the current temperature.
Alert Response Address
The SMBus alert response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex, expensive logic needed to be a bus
master. Upon receiving an
ALERT
interrupt signal, the
host master can broadcast a receive byte transmission
to the alert response slave address (0001 100). Then
any slave device that generated an interrupt attempts
to identify itself by putting its own address on the bus
(Table 3).
The alert response can activate several different slave
devices simultaneously, similar to the I
2
C general call. If
more than one slave attempts to respond, bus arbitra-
tion rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledge and continues to hold the
ALERT
line low
until serviced (implies that the host interrupt input is
M
Multichannel Remote/Local
Temperature Sensors
______________________________________________________________________________________
11
Table 2. Data Format (Two
’
s Complement)
Table 3. Read Format for Alert Response
Address (0001100)
ADD6
ADD5
ADD4
ADD3
ADD2
ADD1
6
5
4
3
2
1
0
Provide the current
MAX1668/MAX1805/MAX1989
slave address that was latched at
POR (Table 8)
FUNCTION
ADD7
7
(MSB)
1
(LSB)
Logic 1
BIT
NAME
DIGITAL OUTPUT DATA BITS
SIGN
MSB
0
111
0
111
0
111
0
111
0
001
0
000
0
000
0
000
0
000
0
000
1
111
1
111
1
110
1
110
1
100
1
100
1
011
1
011
TEMP
(
°
C)
ROUNDED
TEMP
(
°
C)
LSB
1111
1111
1111
1110
1001
0000
0000
0000
0000
0000
1111
1111
0111
0110
1001
1001
1111
1111
+130.00
+127.00
+126.50
+126.00
+25.25
+0.50
+0.25
+0.00
-0.25
-0.50
-0.75
-1.00
-25.00
-25.50
-54.75
-55.00
-65.00
-70.00
+127
+127
+127
+126
+25
+1
+0
+0
+0
+0
-1
-1
-25
-25
-55
-55
-65
-65
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1668MEE | Multichannel Remote/Local Temperature Sensors |
| MAX1989MUE | Multichannel Remote/Local Temperature Sensors |
| MAX167AENG | CMOS 12-Bit A/D Converters With Track-and-Hold |
| MAX167BCNG | CMOS 12-Bit A/D Converters With Track-and-Hold |
| MAX163BENG | CMOS 12-Bit A/D Converters With Track-and-Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1668EVKIT | 功能描述:板上安裝溫度傳感器 Multichannel Remote/Local Temperature Sensors RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1668EVSYS | 功能描述:板上安裝溫度傳感器 Evaluation System for the MAX1668 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1668MEE | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1668MEE+ | 功能描述:板上安裝溫度傳感器 MultiCh Remote Local RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1668MEE+T | 功能描述:板上安裝溫度傳感器 MultiCh Remote Local RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。