參數資料
型號: MAX16049ETN
廠商: Maxim Integrated Products, Inc.
元件分類: 基準電壓源/電流源
英文描述: Hold function, Loop detection; Vin (V) max.: 24; Icc (mA) max.: 6.45; Fmax (kHz) max.: 400; Topr [Tjopr] (°C): -40 to +125; Remarks: Power factor collection; Package: SOP; Pin count: 16
中文描述: 12-Channel/8-Channel EEPROM的可編程系統的故障寄存器經理非易失
文件頁數: 50/62頁
文件大?。?/td> 535K
代理商: MAX16049ETN
M
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
50
______________________________________________________________________________________
Test Access Port (TAP)
Controller State Machine
The TAP controller is a finite state machine that
responds to the logic level at TMS on the rising edge of
TCK. See Figure 14 for a diagram of the finite state
machine. The possible states are described below:
Test-Logic-Reset:
At power-up, the TAP controller is in
the test-logic-reset state. The instruction register con-
tains the IDCODE instruction. All system logic of the
device operates normally. This state can be reached
from any state by driving TMS high for five clock cycles.
Run-Test/Idle:
The run-test/idle state is used between
scan operations or during specific tests. The instruction
register and test data registers remain idle.
Select-DR-Scan:
All test data registers retain their pre-
vious state. With TMS low, a rising edge of TCK moves
the controller into the capture-DR state and initiates a
scan sequence. TMS high during a rising edge on TCK
moves the controller to the select-IR-scan state.
Capture-DR:
Data can be parallel-loaded into the test
data registers selected by the current instruction. If the
instruction does not call for a parallel load or the select-
ed test data register does not allow parallel loads, the
test data register remains at its current value. On the
rising edge of TCK, the controller goes to the shift-DR
state if TMS is low or it goes to the exit1-DR state if TMS
is high.
TEST-LOGIC-RESET
1
1
1
1
0
0
RUN-TEST/IDLE
0
0
0
0
1
1
1
0
0
1
0
1
1
0
1
0
1
SELECT-DR-SCAN
SELECT-IR-SCAN
CAPTURE-DR
CAPTURE-IR
SHIFT-DR
SHIFT-IR
EXIT1-DR
EXIT1-IR
PAUSE-DR
PAUSE-IR
EXIT2-DR
EXIT2-IR
UPDATE-DR
UPDATE-IR
0
0
0
0
1
1
0
1
1
Figure 14. TAP Controller State Diagram
相關PDF資料
PDF描述
MAX16048 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAX16046 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAX16050 Voltage Monitors/Sequencer Circuits with Reverse-Sequencing Capability
MAX1605ETT-T 30V Internal Switch LCD Bias Supply
MAX1605EUT-T 30V Internal Switch LCD Bias Supply
相關代理商/技術參數
參數描述
MAX16049ETN+ 功能描述:監控電路 8Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16049ETN+T 功能描述:監控電路 8Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX1604EAI 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MAX1604EAI+ 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MAX1604EAI+T 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5