- 您現在的位置：買賣IC網 > PDF目錄383327 > MAX16047 (Maxim Integrated Products, Inc.) 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers PDF資料下載
參數資料
| 型號： | MAX16047 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers |
| 中文描述： | 12/8通道EEPROM可編程系統管理器，提供非易失故障寄存器 |
| 文件頁數： | 47/62頁 |
| 文件大?。?/td> | 535K |
| 代理商： | MAX16047 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
M
Command Codes
The MAX16047/MAX16049 use eight command codes
for block read, block write, and other commands. See
Table 26 for a list of command codes.
To initiate a software reboot, send 96h using the send
byte format. A software-initiated reboot is functionally the
same as a hardware-initiated power-on reset. During
boot-up, EEPROM configuration data in the range of 0Fh
to 7Dh is copied to the same register addresses in the
default page.
Send command code 97h to trigger a fault store to
EEPROM. Configure the Critical Fault Log Control register
(r47h) to store ADC conversion results and/or fault flags
in registers once the command code has been sent.
Using command code 98h allows access to the extend-
ed page, which contains registers for ADC conversion
results, and GPIO input/output data. Use command
code 99h to return to the default page.
Send command code 9Ah to access the EEPROM
page. Once command code 9Ah has been sent, all
addresses are recognized as EEPROM addresses only.
Send command code 9Bh to return to the default page.
Block Write
The block write protocol (see Figure 12) allows the
master device to write a block of data (1 byte to 16
bytes) to memory. The destination address should be
preloaded by a previous send byte command; other-
wise the block write command begins to write at the
current address pointer. After the last byte is written,
the address pointer remains preset to the next valid
address. If the number of bytes to be written causes
the address pointer to exceed FFh for EEPROM or 7Dh
for configuration registers, the address pointer stays at
FFh or 7Dh, overwriting this memory address with the
remaining bytes of data. The last data byte sent is
stored at register address FFh. The slave generates a
NACK at step 5 if the command code is invalid or if the
device is busy, and the address pointer is not altered.
The block write procedure is the following:
1) The master sends a START condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends the 8-bit command code for
block write (94h).
5) The addressed slave asserts an ACK on SDA.
6) The master sends the 8-bit byte count (1 byte to 16
bytes), n
7) The addressed slave asserts an ACK on SDA.
8) The master sends 8 bits of data.
9) The addressed slave asserts an ACK on SDA.
10) Repeat steps 8 and 9 n - 1 times.
11) The master sends a STOP condition.
Block Read
The block read protocol (see Figure 12) allows the
master device to read a block of up to 16 bytes from
memory. Read fewer than 16 bytes of data by issuing
an early STOP condition from the master, or by gener-
ating a NACK with the master. The destination address
should be preloaded by a previous send byte com-
mand; otherwise the block read command begins to
read at the current address pointer. If the number of
bytes to be read causes the address pointer to exceed
FFh for the configuration register or EEPROM, the
address pointer stays at FFh and the last data byte
read is from register rFFh. The block read procedure is
the following:
1) The master sends a START condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends 8 bits of the block read com-
mand (95h).
5) The slave asserts an ACK on SDA, unless busy.
6) The master generates a REPEATED START condition.
7) The master sends the 7-bit slave address and a
read bit (high).
Table 26. Command Codes
COMMAND CODE
94h
95h
96h
97h
98h
99h
9Ah
9Bh
ACTION
Write Block
Read Block
Reboot EEPROM in Register File
Trigger Fault Store to EEPROM
Extended Page Access On
Extended Page Access Off
EEPROM Page Access On
EEPROM Page Access Off
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
______________________________________________________________________________________
47
相關PDF資料 |
PDF描述 |
|---|---|
| MAX16047ETN | 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers |
| MAX16049 | Hold function, Loop detection; Vin (V) max.: 24; Icc (mA) max.: 6.45; Fmax (kHz) max.: 400; Topr [Tjopr] (°C): -40 to +125; Remarks: Power factor collection; Package: DIP; Pin count: 16 |
| MAX16049ETN | Hold function, Loop detection; Vin (V) max.: 24; Icc (mA) max.: 6.45; Fmax (kHz) max.: 400; Topr [Tjopr] (°C): -40 to +125; Remarks: Power factor collection; Package: SOP; Pin count: 16 |
| MAX16048 | 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers |
| MAX16046 | 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX16047ACB+ | 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX16047ACB+T | 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX16047ATN+ | 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX16047ATN+T | 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX16047ETN | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR SEQUENCER 56TQFN EP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。