參數資料
型號： MAX16047
廠商： Maxim Integrated Products, Inc.
英文描述： 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
中文描述： 12/8通道EEPROM可編程系統管理器，提供非易失故障寄存器
文件頁數： 23/62頁
文件大小： 535K
代理商： MAX16047
M
Fault-On Power-Up (
FAULTPU
)
GPIO6 indicates a fault during power-up or power-
down when configured as a “fault-on power-up” output.
Under these conditions, all EN_OUT_ voltages are
pulled low and fault data is saved to nonvolatile
EEPROM. See the Faults section.
MARGIN
GPIO6 is configurable as an active-low
MARGIN
input.
Drive
MARGIN
low before varying system voltages above
or below the thresholds to avoid signaling an error. Drive
MARGIN
high for normal operation.
When
MARGIN
is pulled low or r4Dh[1] is a ‘1,’ the mar-
gin function is enabled.
FAULT1
,
FAULT2
, Any_Fault,
and
RESET
are latched in their current state. Threshold
violations will be ignored, and faults will not be logged.
Manual Reset (
MR
)
GPIO4 is configurable to act as an active-low manual
reset input,
MR
. Drive
MR
low to assert
RESET
.
RESET
remains low for the selected reset timeout period after
MR
transitions from low to high. See the
RESET
section
for more information on selecting a reset timeout period.
Watchdog Input (WDI) and Output (WDO)
Set r1Eh[1:0] and r1Dh[7] to ‘110’ to configure GPIO6 as
WDO. Set r1Dh[6:4] to ‘111’ to configure GPIO5 as WDI.
WDO is an open-drain active-low output. See the
Watchdog Timer section for more information about the
operation of the watchdog timer.
Programmable Outputs
(EN_OUT1–EN_OUT12)
The MAX16047 includes twelve programmable outputs,
and the MAX16049 includes eight programmable out-
puts. These outputs are capable of connecting to either
the enable (EN) inputs of a DC-DC or LDO power supply
or to the gates of series-pass MOSFETs for closed-loop
tracking mode, or for charge-pump mode. Selectable
output configurations include: active-low or active-high,
open-drain or push-pull. EN_OUT1–EN_OUT4 are also
configurable for closed-loop tracking, and EN_OUT1–
EN_OUT6 can act as charge-pump outputs with no
closed-loop tracking. Use the registers r1Fh to r22h to
configure outputs. See Table 8 for detailed information
on configuring EN_OUT1–EN_OUT12.
Table 7.
FAULT1
and
FAULT2
Output Configuration and Dependencies (continued)
REGISTER/
EEPROM
ADDRESS
BIT RANGE
DESCRIPTION
[0]
[1]
[2]
[3]
1 =
FAULT2
is a digital output dependent on MON9*
1 =
FAULT2
is a digital output dependent on MON10*
1 =
FAULT2
is a digital output dependent on MON11*
1 =
FAULT2
is a digital output dependent on MON12*
[4]
1 =
FAULT2
is a digital output that depends on the overvoltage thresholds at the input
selected by r17h and r18h[3:0]
[5]
1 =
FAULT2
is a digital output that depends on the undervoltage thresholds at the
input selected by r17h and 18h[3:0]
[6]
1 =
FAULT2
is a digital output that depends on the early warning thresholds at the
input selected by r17h and r18h[3:0]
18h
[7]
0 =
FAULT2
is an active-low digital output
1 =
FAULT2
is an active-high digital output
*MAX16047 only
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
______________________________________________________________________________________
23
相關PDF資料
PDF描述
MAX16047ETN 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAX16049 Hold function, Loop detection; Vin (V) max.: 24; Icc (mA) max.: 6.45; Fmax (kHz) max.: 400; Topr [Tjopr] (°C): -40 to +125; Remarks: Power factor collection; Package: DIP; Pin count: 16
MAX16049ETN Hold function, Loop detection; Vin (V) max.: 24; Icc (mA) max.: 6.45; Fmax (kHz) max.: 400; Topr [Tjopr] (°C): -40 to +125; Remarks: Power factor collection; Package: SOP; Pin count: 16
MAX16048 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAX16046 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
相關代理商/技術參數
參數描述
MAX16047ACB+ 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16047ACB+T 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16047ATN+ 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16047ATN+T 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16047ETN 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR SEQUENCER 56TQFN EP - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*