- 您現在的位置：買賣IC網 > PDF目錄383325 > MAX1537A (Maxim Integrated Products, Inc.) High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1537A |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook Computers |
| 中文描述： | 高效率、5路輸出、主電源控制器，用于筆記本電腦 |
| 文件頁數： | 34/38頁 |
| 文件大?。?/td> | 1427K |
| 代理商： | MAX1537A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁
M
High-Efficiency, 5x Output, Main Power-Supply
Controllers for Notebook Computers
34
______________________________________________________________________________________
above the feedback-threshold voltage, the controller
does not trigger an on-time pulse, effectively skipping a
cycle. This allows the controller to maintain regulation
above the maximum input voltage, but forces the con-
troller to effectively operate with a lower switching fre-
quency. This results in an input threshold voltage at
which the controller begins to skip pulses (V
IN(SKIP)
):
where f
OSC
is the switching frequency selected by FSEL.
PC Board Layout Guidelines
Careful PC board layout is critical to achieving low
switching losses and clean, stable operation. The
switching power stage requires particular attention
(Figure 11). If possible, mount all of the power compo-
nents on the top side of the board, with their ground
terminals flush against one another. Follow these guide-
lines for good PC board layout:
Keep the high-current paths short, especially at the
ground terminals. This practice is essential for sta-
ble, jitter-free operation.
Keep the power traces and load connections short.
This practice is essential for high efficiency. Using
thick copper PC boards (2oz vs. 1oz) can enhance
full-load efficiency by 1% or more. Correctly routing
PC board traces is a difficult task that must be
approached in terms of fractions of centimeters,
where a single m
Ω
of excess trace resistance caus-
es a measurable efficiency penalty.
Minimize current-sensing errors by connecting CSH_
and CSL_ directly across the current-sense resistor
(R
SENSE_
).
When trade-offs in trace lengths must be made, it is
preferable to allow the inductor charging path to be
made longer than the discharge path. For example,
it is better to allow some extra distance between the
input capacitors and the high-side MOSFET than to
allow distance between the inductor and the low-
side MOSFET or between the inductor and the out-
put filter capacitor.
Route high-speed switching nodes (BST_, LX_, DH_,
and DL_) away from sensitive analog areas (REF,
FB_, CSH_, CSL_).
Layout Procedure
1) Place the power components first, with ground termi-
nals adjacent (N
L
_ source, C
IN
, C
OUT
_, and D
L
_
anode). If possible, make all these connections on
the top layer with wide, copper-filled areas.
2) Mount the controller IC adjacent to the low-side
MOSFET, preferably on the back side opposite N
L_
and N
H_
to keep LX_, GND, DH_, and the DL_ gate-
drive lines short and wide. The DL_ and DH_ gate
traces must be short and wide (50 to 100 mils wide if
the MOSFET is 1 inch from the controller IC) to keep
the driver impedance low and for proper adaptive
dead-time sensing.
3) Group the gate-drive components (BST_ diode and
capacitor, LDO5 bypass capacitor) together near
the controller IC.
4) Make the DC-DC controller ground connections as
shown in Figures 1 and 11. This diagram can be
viewed as having two separate ground planes:
power ground, where all the high-power compo-
nents go; and an analog ground plane for sensitive
analog components. The analog ground plane and
power ground plane must meet only at a single point
directly at the IC.
5) Connect the output power planes directly to the out-
put-filter-capacitor positive and negative terminals
with multiple vias. Place the entire DC-DC converter
circuit as close to the load as is practical.
V
V
f
t
IN SKIP
(
OUT
OSC
ON MIN
(
)
)
=
1
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1533 | High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook Computers |
| MAX1533ETJ | High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook Computers |
| MAX1537ETX | High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook Computers |
| MAX153MJP | 1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-Down |
| MAX153EWP | 1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-Down |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1537AETX+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1537ETX | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1537ETX-T | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1537EVKIT | 制造商:Maxim Integrated Products 功能描述:MAIN POWER SUPPLY CONTROLLER FOR NOTEBOOK - Bulk |
| MAX1538ETI | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。