- 您現在的位置：買賣IC網 > PDF目錄383324 > MAX1512ETA (MAXIM INTEGRATED PRODUCTS INC) 16-Bit Transceivers With Parity Generators / Checkers And 3-State Outputs 56-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MAX1512ETA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | 16-Bit Transceivers With Parity Generators / Checkers And 3-State Outputs 56-SSOP -40 to 85 |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, DSO8 |
| 封裝： | 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEC, TDFN-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 682K |
| 代理商： | MAX1512ETA |
Applications Information
The VCOM adjustment and the EEPROM programming
must be performed with an external programming cir-
cuit. Refer to the MAX1512 evaluation kit for a complete
programming circuit solution.
Use a circuit similar to the conceptual diagram shown
in Figure 8 to drive CTL. The accuracy of the program-
ming voltage (V
PP
) is critical for proper MAX1512 data
retention. The use of a comparator is recommended to
verify the correct programming voltage has been
reached. A complete design example of a CTL pro-
gramming circuit is presented in the MAX1512 evalua-
tion kit data sheet.
Electrostatic Discharge (CTL)
The CTL pin is exposed at the LCD panel connector and
is subject to electrostatic discharge (ESD). Often an RC
filter is used to improve an input’s resilience to ESD. If a
filter is added between the LCD panel connector and
CTL, ensure that the RC time constant is short enough to
avoid interfering with CTL pulses or the EEPROM pro-
gramming timing. An RC time constant less than 200μs
does not interfere with EEPROM programming.
Leakage Current (CTL)
The CTL pin is internally biased to V
DD
/ 2, but it is sen-
sitive to leakage currents above 0.1μA. When CTL is
not driven, avoid leakage currents around the CTL pin.
Otherwise, reinforce the V
DD
/ 2 set point with an exter-
nal resistive voltage-divider.
Layout Information
Use the following guidelines for good layout:
Place the VCOM buffer and the R1/R2 voltage-
divider close to the OUT pin (Figure 1). Keep the
VCOM buffer and the R1/R2 voltage-divider close
to each other.
Place R
SET
close to SET.
In noisy environments, bypass capacitors may be
desired on V
DD
and/or V
AVDD
. Keep any bypass
capacitors close to the IC with short connections to
the pins.
Refer to the MAX1512 evaluation kit for an example of
proper board layout.
M
EEPROM-Programmable TFT VCOM Calibrator
______________________________________________________________________________________
11
DAC
0 TO 2.5V
μ
C
USER
INTERFACE
CTL
MAX1512
REF
0 TO 15.5V
V
PP
VERIFY
Figure 8. Conceptual Programming Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1512 | EEPROM-Programmable TFT VCOM Calibrator |
| MAX1515 | Low-Voltage, Internal Switch, Step-Down/DDR Regulator |
| MAX1515ETG | Low-Voltage, Internal Switch, Step-Down/DDR Regulator |
| MAX1516 | TFT-LCD DC-DC Converters with Operational Amplifiers |
| MAX1516ETJ | TFT-LCD DC-DC Converters with Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1512ETA+ | 制造商:Maxim Integrated Products 功能描述:EEPROM-PROGRAMMABLE TFT VCOM CALIBRATOR - Rail/Tube |
| MAX1512ETA+T | 功能描述:LCD Gamma緩沖器 EEPROM-Prog TFT VCOM Calibrator RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX1512ETA+TG104 | 制造商:Maxim Integrated Products 功能描述:EEPROM-PROGRAMMABLE TFT VCOM CALIBRATOR - Tape and Reel |
| MAX1512ETA-T | 功能描述:LCD Gamma緩沖器 RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX1512EVKIT | 制造商:Maxim Integrated Products 功能描述:#EMPTY - Bulk |
發布緊急采購，3分鐘左右您將得到回復。