- 您現(xiàn)在的位置：買賣IC網 > PDF目錄383324 > MAX1512ETA (MAXIM INTEGRATED PRODUCTS INC) 16-Bit Transceivers With Parity Generators / Checkers And 3-State Outputs 56-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MAX1512ETA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | 16-Bit Transceivers With Parity Generators / Checkers And 3-State Outputs 56-SSOP -40 to 85 |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, DSO8 |
| 封裝： | 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEC, TDFN-8 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 682K |
| 代理商： | MAX1512ETA |
M
To avoid unintentional VCOM adjustment, the MAX1512
is guaranteed to reject CTL pulses shorter than 20μs. In
addition, to avoid the possibility of a single false pulse
caused by power-up sequencing between V
DD
and
CTL, the very first pulse is ignored.
EEPROM Programming (CTL)
To program the EEPROM, apply the EEPROM program-
ming waveform through the CTL interface (Figure 7).
The control interface delivers programming power and
DAC adjustment commands on the same wire. This
1-wire approach minimizes the number of connections
from the programming circuit to the LCD panel.
To apply the EEPROM programming waveform, carefully
ramp CTL from midscale (V
DD
/ 2) to the programming
voltage, V
PP
, in 7.5ms as shown in Figure 7. If the ramp
is generated digitally, use at least 45 steps to achieve
the required 320mV ramp resolution. During the ramp
time, VCOM adjustment is disabled and the EEPROM
cells are biased in preparation for programming. After
reaching V
PP
, hold CTL at V
PP
for 1ms. During the
EFPROM program time, the EEPROM stores the DAC
setting. Next, drive CTL to ground in less than 1ms and
hold for at least 200μs. Finally, drive CTL to V
DD
/ 2 to
complete the write cycle. The EEPROM is factory set to
half scale. Follow the
EEPROM Programming Spec-
ifications
in Table 1 to guarantee reliable EEPROM pro-
gramming. Violating the specifications can damage the
EEPROM or affect data retention.
A complete evaluation kit is available to simplify evalua-
tion and production development.
EEPROM-Programmable TFT VCOM Calibrator
10
______________________________________________________________________________________
Table 1. EEPROM Programming Specifications
PARAMETER
SYMBOL
V
PP
T1
T2
T3
T4
MIN
15.25
7.0
0.9
10
200
TYP
15.5
7.5
1.0
MAX
15.75
8.0
1.1
1000
UNITS
V
ms
ms
μs
μs
CTL Programming Voltage
CTL Programming Ramp
EEPROM Program Time
V
PP
Fall Time
Done Hold Time
0
V
PP
CTL VOLTAGE
TIME
V
DD
/ 2
T1
T2
T4
T3
Figure 7. EEPROM Programming
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1512 | EEPROM-Programmable TFT VCOM Calibrator |
| MAX1515 | Low-Voltage, Internal Switch, Step-Down/DDR Regulator |
| MAX1515ETG | Low-Voltage, Internal Switch, Step-Down/DDR Regulator |
| MAX1516 | TFT-LCD DC-DC Converters with Operational Amplifiers |
| MAX1516ETJ | TFT-LCD DC-DC Converters with Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1512ETA+ | 制造商:Maxim Integrated Products 功能描述:EEPROM-PROGRAMMABLE TFT VCOM CALIBRATOR - Rail/Tube |
| MAX1512ETA+T | 功能描述:LCD Gamma緩沖器 EEPROM-Prog TFT VCOM Calibrator RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX1512ETA+TG104 | 制造商:Maxim Integrated Products 功能描述:EEPROM-PROGRAMMABLE TFT VCOM CALIBRATOR - Tape and Reel |
| MAX1512ETA-T | 功能描述:LCD Gamma緩沖器 RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX1512EVKIT | 制造商:Maxim Integrated Products 功能描述:#EMPTY - Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。