參數資料
型號: MAX1497EPI
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: ADC
英文描述: 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface
中文描述: 1-CH PROPRIETARY METHOD ADC, PDIP28
封裝: 0.600 INCH, PLASTIC, MS-011AB, DIP-28
文件頁數: 16/33頁
文件大?。?/td> 665K
代理商: MAX1497EPI
M
3.5- and 4.5-Digit, Single-Chip ADCs with LED
Drivers and μC Interface
16
______________________________________________________________________________________
Figure 15 shows the MAX1497/MAX1499 operating with
an external differential reference. In this mode, REF- is
connected to the top of the strain gauge and REF+ is
connected to the midpoint of the resistor-divider of
the supply.
Applications Information
Serial Interface
The SPI/QSPI/MICROWIRE serial interface consists of a
chip select (
CS
), a serial clock (SCLK), a data in (DIN),
a data out (DOUT), and an asynchronous
EOC
output.
EOC
provides an asynchronous end-of-conversion sig-
nal with a period of 200ms (f
CLK
= 4.9152MHz). The
MAX1497 updates the data register when
EOC
goes
high. Data is valid in the ADC result registers when
EOC
returns low. The serial interface provides access
to 12 on-chip registers, allowing control to all the power
modes and functional blocks. Table 5 lists the address
and read/write accessibility of all the registers.
A logic high on
CS
tri-states DOUT and causes the
MAX1497/MAX1499 to ignore any signals on SCLK and
DIN. To clock data in or out of the internal shift register,
drive
CS
low. SCLK synchronizes the data transfer. The
rising edge of SCLK clocks DIN into the shift register,
and the falling edge of SCLK clocks DOUT out of the
shift register. DIN and DOUT are transferred MSB first
(data is left justified). Figures 8–12 show the detailed
serial interface timing diagrams for the 8- and 16-bit
read/write operations.
All communication with the MAX1497/MAX1499 begins
with a command byte on DIN, where the first logic one
on DIN is recognized as the START bit (MSB) for the
command byte. The following seven clock cycles load
the command into a shift register. These 7 bits specify
which of the registers are accessed next, and whether
a read or write operation takes place. Transitions on the
serial clock after the command byte transfer, cause a
write or read from the device until the correct number of
CS
SCLK
DIN
DOUT
t
CSH
t
CL
t
DS
t
DH
t
DV
t
CH
t
DO
t
TR
t
CSH
t
CSS
Figure 8. Detailed Timing Diagram
SCLK
CS
DIN
DOUT
1
0
RS4 RS3
RS2
RS1
D7
D6
D5
D4
D3
D2
D1
D0
D8
D9
RS0
x
D15
D14
D13
D12
D11
D10
CONTROL BYTE
DATA BYTE
Figure 9. Serial-Interface, 16-Bit, Write Timing Diagram
相關PDF資料
PDF描述
MAX1497 3.5- and 4.5-Digit. Single-Chip ADCs with LED Drivers and 礐 Interface
MAX1499 3.5- and 4.5-Digit. Single-Chip ADCs with LED Drivers and 礐 Interface
MAX1497EAI 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface
MAX1499ECJ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface
MAX15004 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
相關代理商/技術參數
參數描述
MAX1497EPI+ 功能描述:模數轉換器 - ADC 3.5 Digit ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX14980ETO+ 制造商:Maxim Integrated Products 功能描述:6 GBPS QUAD SAS/SATA REDRIVER WITH EQUALIZATION - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC REDRIVER 6GBPS SAS/SATA QFN 制造商:Maxim Integrated Products 功能描述:6G/PS Quad SAS/SATA redriver with eq
MAX14980ETO+T 制造商:Maxim Integrated Products 功能描述:- Tape and Reel 制造商:Maxim Integrated Products 功能描述:MAX14980ETO+T
MAX14982ETO+ 制造商:Maxim Integrated Products 功能描述:SINGLE LANE 2:1 / 1:2 MUX + REDRIVER WITH EQUALIZATION - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC EQUALIZER/REDRVR 42TQFN
MAX14982ETO+T 制造商:Maxim Integrated Products 功能描述:1:2 / 2:1 PCIE GEN 2 MUX + REDRIVER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC EQUALIZER/REDRVR 42TQFN