- 您現在的位置：買賣IC網 > PDF目錄383320 > MAX1457CCJ (MAXIM INTEGRATED PRODUCTS INC) 0.1%-Accurate Signal Conditioner for Piezoresistive Sensor Compensation PDF資料下載
參數資料
| 型號： | MAX1457CCJ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | 0.1%-Accurate Signal Conditioner for Piezoresistive Sensor Compensation |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PQFP32 |
| 封裝： | TQFP-32 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 93K |
| 代理商： | MAX1457CCJ |
Pressure Nonlinearity Correc tion
The MAX1457 corrects pressure nonlinearity in an ana-
log fashion by providing a resistive feedback path
(resistor R
LIN
in Figure 4) from a buffered main output
(LINOUT pin) to the current source (ISRC pin). The
feedback coefficient is then set by writing a 16-bit word
to the FSO LIN DAC.
For many silicon sensors, this type of nonlinearity cor-
rection may reduce sensor nonlinearity by an order of
magnitude.
_____________Applic ations Information
Ratiometric Output Configuration
Ratiometric output configuration provides an output that
is proportional to the power-supply voltage. When used
with ratiometric ADCs, this output provides digital pres-
sure values independent of supply voltage.
The MAX1457 has been designed to provide a high-
performance ratiometric output with a minimum number
of external components (Figure 5). These external com-
ponents typically include an external EEPROM (93C66),
decoupling capacitors, and resistors.
2-Wire, 4–20mA Configuration
In this configuration, a 4mA current is used to power a
transducer, and an incremental current of 0 to 16mA
proportional to the measured pressure is transmitted
over the same pair of wires. Current output enables
long-distance transmission without a loss of accuracy
due to cable resistance.
Only a few components (Figure 6) are required to build
a 4–20mA output configuration. A low-quiescent-cur-
rent voltage regulator with a built-in bandgap reference
(such as the REF02) should be used. Since the
MAX1457 performs temperature and gain compensa-
tion of the circuit, the temperature stability and calibra-
tion accuracy of the reference voltage is of secondary
importance.
The external transistor forms the controllable current
loop. The MAX1457 controls the voltage across resistor
R
A
. With R
A
= 50
, a 0.2V to 1.0V range would be
required during the calibration procedure. If needed,
the PGA output can be divided using resistors R
B
and
R
C
.
For overvoltage protection, place a Zener diode across
V
IN-
and V
IN+
(Figure 6). A feedthrough capacitor
across the inputs reduces EMI/RFI.
T est S ystem Configuration
The MAX1457 is designed to support an automated
production pressure-temperature test system with inte-
grated calibration and temperature compensation.
Figure 7 shows the implementation concept for a low-
cost test system capable of testing up to five transduc-
er modules connected in parallel. Three-state outputs
on the MAX1457 allow for parallel connection of trans-
ducers.
The test system shown in Figure 7 includes a dedicated
test bus consisting of six wires (the capacitive loading
of each transducer module should not exceed the
EEPROM fan-out specifications):
Two power-supply lines
One analog output voltage line from the transducers
to a system digital voltmeter
Three MicroWire/SPI interface lines: EDI (data-in),
EDO (data-out), and ECLK (clock)
For simultaneous testing of more than five transducer
modules, use buffers to prevent overloading the data bus.
A digital multiplexer controls the two chip-select signals
for each transducer:
Module Select (MCS) places the selected module
into an active state, enabling operation and compen-
sation
EEPROM Select (ECS) enables writing to the trans-
ducer’s EEPROM
M
0.1%-Ac c urate S ignal Conditioner
for Piezoresistive S ensor Compensation
_______________________________________________________________________________________
7
V
BR
V
OUT
I
BR
R
LIN
V
DD
PGA
FSO
LIN
DAC
111...1
16 BIT
Figure 4. Pressure Nonlinearity Correction
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1457CWI | 0.1%-Accurate Signal Conditioner for Piezoresistive Sensor Compensation |
| MAX1457AWI | 0.1%-Accurate Signal Conditioner for Piezoresistive Sensor Compensation |
| MAX1470EVKIT-315 | MAX1470 Evaluation Kit |
| MAX1470EVKIT-433 | MAX1470 Evaluation Kit |
| MAX1472EVKIT-315 | Evaluation Kit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1457EVKIT-NS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX14580EETE+C77 | 制造商:Maxim Integrated Products 功能描述:USB BATTERY CHARGER DETECTORS - Rail/Tube |
| MAX14581EWC+T | 功能描述:USB 接口集成電路 3/5 Wire Full Speed USB Trnsvr RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX14582EWC+T | 功能描述:USB 接口集成電路 3/5 Wire Full Speed USB Trnsvr RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX14583EEWE+T | 功能描述:多路器開關 IC High Density 8:1 MUX I2C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。