參數資料
型號： MAX1415CWE
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： ADC
英文描述： 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
中文描述： 2-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16
封裝： 0.300 INCH, MS-013AA, SOP-16
文件頁數： 32/36頁
文件大小： 669K
代理商： MAX1415CWE
M
Applications Information
Applications Examples
Strain-Gauge Measurement
Connect the differential inputs of the MAX1415/
MAX1416 to the bridge network of the strain gauge. In
Figure 12, the analog positive supply voltage powers the
bridge network and the MAX1415/MAX1416 along with
the reference voltage in a ratiometric configuration. The
on-chip PGA allows the MAX1415/MAX1416 to handle an
analog input voltage range as low as 20mV to full scale.
Optical Isolation
For applications that require an optically isolated inter-
face, see Figure 13. With 6N136-type optocouplers, the
maximum clock speed is 4MHz. The maximum clock
speed is limited by the degree of mismatch between
the individual optocouplers. Faster optocouplers allow
faster signaling at a higher cost.
Layout, Grounding, and Bypassing
Use PC boards with separate analog and digital
ground planes. Connect the two ground planes togeth-
er at the MAX1415/MAX1416 GND. Isolate the digital
supply from the analog with a low-value resistor (10
)
or ferrite bead when the analog and digital supplies
come from the same source.
Ensure that digital return currents do not pass through
the analog ground and that return-current paths are low
impedance. A 5mA current flowing through a PC board
ground trace impedance of only 0.05
creates an error
voltage of approximately 250μV.
Layout the PC board to ensure digital and analog signal
lines are kept separate. Do not run digital lines (especial-
ly the SCLK and DOUT) parallel to any analog lines. If
they must cross one another, do so at right angles.
Bypass V
DD
to the analog ground plane with a 0.1μF
capacitor in parallel with a 1μF to 10μF low-ESR capac-
itor. Keep capacitor leads short for best supply-noise
rejection. Bypass REF+, REF-, and all analog inputs
with a 0.1μF capacitor to GND. Place all bypass capac-
itors as close to the device as possible to achieve the
best decoupling.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line is either a best-straight-line fit or a line
drawn between the endpoints of the transfer function,
once offset and gain errors have been nullified. INL for
the MAX1415/MAX1416 is measured using the end-
point method. This is the more conservative method.
Unipolar Offset Error
For an ideal converter, the first transition occurs at 0.5
LSB above zero. Offset error is the amount of deviation
between the measured first transition point and the
ideal point.
Bipolar Zero Error
In bipolar mode, the ideal midscale transition occurs at
AIN+ - AIN- = 0. Bipolar zero error is the measured
deviation from this ideal value.
Gain Error
With a full-scale analog input voltage applied to the
ADC (resulting in all ones in the digital code), gain error
is defined as the amount of deviation between the ideal
transfer function and the measured transfer function
(with the offset error or bipolar zero error removed).
Gain error is usually expressed in LSB or a percent of
full-scale range (%FSR).
Positive Full-Scale Error
For the ideal transfer curve, the code edge transition
that causes a full-scale transition to occur is 1.5 LSB
below full scale. The positive full-scale error is the dif-
ference between this code transition of the ideal trans-
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADCs
32
______________________________________________________________________________________
MAX1415
MAX1416
V
DD
CLKIN
REF+
REF-
AIN1+
AIN1-
CLKOUT
CS
SCLK
DIN
DOUT
DRDY
RESET
GND
V
DD
R
REF
ACTIVE
GAUGE
DUMMY
GAUGE
0.1
μ
F
10
μ
F
0.1
μ
F
0.1
μ
F
R
R
0.1
μ
F
0.1
μ
F
Figure 12. Strain Gauge Measurement
相關PDF資料
PDF描述
MAX1415ENE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415EUE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415EWE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1418 15-Bit, 100Msps ADC with -77.7dBFS Noise Floor for Baseband Applications
MAX1419 15-Bit, 100Msps ADC with -77.7dBFS Noise Floor for Baseband Applications
相關代理商/技術參數
參數描述
MAX1415ENE 制造商:Maxim Integrated Products 功能描述:16-BIT, LOW-POWER, 2-CHANNEL, SIGMA-DELTA ADC - Rail/Tube
MAX1415EPE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415EPE+ 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415EUE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415EUE+ 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*