參數資料
型號： MAX1415AEWE
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： ADC
英文描述： 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
中文描述： 2-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16
封裝： 0.300 INCH, MS-013AA, SOIC-16
文件頁數： 24/36頁
文件大?。?/td> 669K
代理商： MAX1415AEWE
M
The default state of the MAX1415/MAX1416 is to wait
for a write to the communications register. Any write or
read operation on the MAX1415/MAX1416 is a two-step
process. First, a command byte is written to the com-
munications register. This command selects the input
channel, the desired register for the next read or write
operation, and whether the next operation is a read or a
write. The second step is to read from or write to the
selected register. At the end of the data-transfer cycle,
the device returns to the default state. See the
Performing a Conversion
section for examples.
If the serial communication is lost, write 32 ones to the ser-
ial interface to return the MAX1415/MAX1416 to the default
state. The registers are not reset after this operation.
Communications Register
The byte-wide communications register is bidirectional
so it can be written and read. The byte written to the
communications register indicates the next read or write
operation on the selected register, the power-down
mode, and the analog input channel (see Table 6). The
DRDY
bit indicates the conversion status.
0/
DRDY
:
(Default = 0) Communication-Start/Data-Ready
Bit. Write a 0 to the 0/
DRDY
bit to start a write operation to
the communications register. If 0/
DRDY
= 1, then the
device waits until a 0 is written to 0/
DRDY
before continu-
ing to load the remaining bits. For a read operation, the
0/
DRDY
bit shows the status of the conversion. The
DRDY
bit returns a 0 if the conversion is complete and
the data is ready.
DRDY
returns a 1 if the new data has
been read and the next conversion is not yet complete. It
has the same value as the
DRDY
output pin.
RS2, RS1, RS0:
(Default = 0, 0, 0) Register-Select Bits.
RS2, RS1, and RS0 select the next register to be
accessed as shown in Table 7.
R/
W
:
(Default = 0) Read-/Write-Select Bit. Use this bit to
select if the next register access is a read or a write
operation. Set R/
W
= 0 to select a write operation, or set
R/
W
= 1 for a read operation on the selected register.
PD:
(Default = 0) Power-Down Control Bit. Set PD = 1
to initiate power-down mode. Set PD = 0 to take the
device out of power-down mode. If the internal oscilla-
tor or external crystal/resonator is used and CLKDIS =
0, CLKOUT remains active during power-down mode to
provide a clock source for other devices in the system.
CH1, CH0:
(Default = 0, 0) Channel-Select Bit. Write to
the CH1 and CH0 bits to select the conversion channel or
to access the calibration data shown in Table 8. The cali-
bration coefficients of a particular channel are stored in
one of the three offset and gain register pairs in Table 8.
Set CH1 = 1 and CH0 = 0 to evaluate the noise perfor-
mance of the part without external noise sources. In this
noise-evaluation mode, connect AIN1- to an external volt-
age within the allowable common-mode range.
Setup Register
The byte-wide setup register is bidirectional so it can
be written and read. The byte written to the setup regis-
ter sets the calibration modes, PGA gain, unipolar/bipo-
lar mode, buffer enable, and conversion start (see
Table 9).
MD1, MD0:
(Default = 0, 0) Mode-Select Bits. See
Table 10 for normal operating mode, self-calibration,
zero-scale calibration, or full-scale calibration-mode
selection.
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADCs
24
______________________________________________________________________________________
SETUP REGISTER (8 BITS)
RS2 RS1 RS0
CLOCK REGISTER (8 BITS)
DATA REGISTER (16 BITS)
TEST REGISTER (8 BITS)*
OFFSET REGISTER (24 BITS)
GAIN REGISTER (24 BITS)
COMMUNICATIONS REGISTER
REGISTER
SELECT
DECODER
DIN
DOUT
*THE TEST REGISTER IS USED FOR FACTORY TESTING ONLY.
Figure 10. Register Summary
相關PDF資料
PDF描述
MAX1415CNE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415CUE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415CWE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415ENE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
MAX1415EUE 16-Bit, Low-Power, 2-Channel, Sigma-Delta ADCs
相關代理商/技術參數
參數描述
MAX1415AEWE+ 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415AEWE+T 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415AEWE-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1415ENE 制造商:Maxim Integrated Products 功能描述:16-BIT, LOW-POWER, 2-CHANNEL, SIGMA-DELTA ADC - Rail/Tube
MAX1415EPE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*