參數資料
型號: MAX132MRG
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: ADC
英文描述: 【18-Bit ADC with Serial Interface
中文描述: 1-CH 18-BIT MULTI-SLOPE ADC, SERIAL ACCESS, CDIP24
封裝: CERDIP-24
文件頁數: 7/16頁
文件大?。?/td> 129K
代理商: MAX132MRG
M
±18-Bit ADC with S erial Interfac e
_______________________________________________________________________________________
7
±660mV for 60Hz mode operation or between ±390mV
and ±550mV for 50Hz mode operation. The pseudo-
differential input voltage is applied across pins 14 and
15 (IN HI, IN LO), and can range to within 2V of either
supply rail.
The inputs IN HI and IN LO lead directly to CMOS tran-
sistor gates, yielding extremely high input impedances
that are useful when converting signals from a high
input source impedance, such as a sensor. Input cur-
rents are only 2pA typical at +25°C. Figure 6 shows an
RC filter at the input to optimize noise performance.
Fault protection is accomplished by the 100k
series
resistance. Internal protection diodes, which clamp the
analog inputs from V+ to V-, allow the channel input
pins to swing from (V- - 0.3V) to (V+ + 0.3V) without
damage. However, if the analog input voltage at the
pins IN HI or IN LO exceed the supplies, limit the cur-
rent into the device to less than 1mA, as excessive cur-
rent will damage the device.
Referenc e V oltage S elec tion
The reference voltage sets the analog input voltage
range. For the nominal ±512mV full-scale input range, a
545mV reference voltage is used for the 60Hz mode
and a 655mV reference voltage is used in the 50Hz mode.
The reference voltage can be calculated as follows:
The recommended reference voltage range is 500mV
to 700mV. The MAX132 is tested with the nominal
545mV reference voltage in 60Hz mode. Use amplifiers
or attenuators (resistor dividers) to scale other full-scale
input signal ranges to the recommended ±512mV full-
scale range.
References outside the recommended range may be
used with a degradation of linearity. A reference volt-
age from 200mV to 500mV will result in a lower signal-
to-noise ratio; a reference voltage from 700mV to 2V will
increase the rollover error.
The MAX872 2.50V reference, with its 10μA supply cur-
rent, is ideally suited for the MAX132. Figure 7 shows
how 2.50V can be divided to obtain the desired refer-
ence voltage. The reference input accepts voltages
anywhere within the converter’s power-supply range;
however, for best performance, neither REF+ nor REF-
should come within 2V of the supplies.
MAX132
IN LO
AGND
IN HI
DE+
DE+
REF+
CREF+
C
REF
REF-
CREF-
INT IN
INT OUT
INTEGRATOR
COMPARATOR 1
COMPARATOR 2
DE-
BUFFER
8pF
64pF
Z1+ x 8
C
INT
R
INT
BUFFER
DE-
TO
DIGITAL
SECTION
INT
REST
INT
INT
X8
DE
DE
Figure 5. Analog Section Block Diagram
60
545
(
512
262144
,
50
655
(
512
262144
,
Hz Mode
V
counts
V
or
Hz Mode
V
counts
V
REF
IN FS
(
REF
IN FS
(
:
) (
)
)
:
) (
)
)
)
)
=
=
相關PDF資料
PDF描述
MAX132CWG 【18-Bit ADC with Serial Interface
MAX132EVKIT MAX132 EVALUATION KIT
MAX132ENG 【18-Bit ADC with Serial Interface
MAX1332 3Msps/2Msps, 5V/3V, 2-Channel, True-Differential 12-Bit ADCs
MAX1333 18-Bit Bus-Interface D-Type Latches With 3-State Outputs 56-SSOP -40 to 85
相關代理商/技術參數
參數描述
MAX1330 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX13300EVKIT+ 功能描述:音頻 IC 開發工具 MAX13300/01 EVAL KIT RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
MAX13301AUM/V+ 制造商:Maxim Integrated Products 功能描述:4-CHANNEL, AUTOMOTIVE CLASS D AUDIO AMPLIFIER - Rail/Tube
MAX13301AUM/V+T 制造商:Maxim Integrated Products 功能描述:4-CHANNEL, AUTOMOTIVE CLASS D AUDIO AMPLIFIER - Tape and Reel
MAX13301EVKIT# 功能描述:放大器 IC 開發工具 MAX13301 EVAL KIT RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V