- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX1303BEUP+ (Maxim Integrated Products)IC ADC 16BIT MULT RANGE 20TSSOP PDF資料下載
參數資料
| 型號： | MAX1303BEUP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/29頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT MULT RANGE 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 標準包裝： | 74 |
| 位數： | 16 |
| 采樣率（每秒）： | 115k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 879mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Full Power-Down Mode (Mode 7)
When M[2:0] = 111, the device enters full power-down
mode and the total supply current falls to 1A (typ). In full
power-down, all analog portions of the device are powered
down. When using the internal reference, upon exiting full
power-down mode, allow 10ms for the internal reference
voltage to stabilize prior to initiating a conversion.
To exit full power-down, change the mode by issuing
one of the following mode-control bytes (see the
Mode
Control section):
External-clock-mode control byte
External-acquisition-mode control byte
Internal-clock-mode control byte
Reset byte
Partial power-down-mode control byte
This prevents the MAX1303 from inadvertently exiting
full power-down mode because of a CS glitch in a noisy
digital environment.
Power-On Reset
The MAX1303 powers up in normal operation config-
ured for external clock mode with all circuitry active
(Tables 7 and 8). Each analog input channel
(CH0–CH7) is set for single-ended conversions with a
±VREF bipolar input range (Table 6).
Allow the power supplies to stabilize after power-up. Do
not initiate any conversions until the power supplies
have stabilized. Additionally, allow 10ms for the internal
reference to stabilize when CREF = 1.0F and CRECAP
= 0.1F. Larger reference capacitors require longer
stabilization times.
Internal or External Reference
The MAX1303 operates with either an internal or external
reference. The reference voltage impacts the ADC’s FSR
(Figures 11, 12, and 13). An external reference is recom-
mended if more accuracy is required than the internal ref-
erence provides, and/or multiple converters require the
same reference voltage.
Internal Reference
The MAX1303 contains an internal 4.096V bandgap refer-
ence. This bandgap reference is connected to REFCAP
through a nominal 5k
resistor (Figure 16). The voltage at
REFCAP is buffered creating 4.096V at REF. When using
the internal reference, bypass REFCAP with a 0.1F or
greater capacitor to AGND1 and bypass REF with a
1.0F or greater capacitor to AGND1.
External Reference
For external reference operation, disable the internal
reference and reference buffer by connecting REFCAP
to AVDD1. With AVDD1 connected to REFCAP, REF
becomes a high-impedance input and accepts an
external reference voltage. The MAX1303 external ref-
erence current varies depending on the applied refer-
ence voltage and the operating mode (see the External
Reference Input Current vs. External Reference Input
Voltage in the
Typical Operating Characteristics).
MAX1303
4-Channel, ±VREF Multirange Inputs,
Serial 16-Bit ADC
24
______________________________________________________________________________________
REF
REFCAP
AGND1
4.096V
BANDGAP
REFERENCE
5k
1x
SAR
ADC REF
4.096V
1.0
F
0.1
F
VRCTH
MAX1303
Figure 16. Internal Reference Operation
M2
M1
M0
MODE
0
External Clock (DEFAULT)
0
1
External Acquisition
0
1
0
Internal Clock
0
1
Reserved
1
0
Reset
1
0
1
Reserved
1
0
Partial Power-Down
1
Full Power-Down
Table 8. Mode-Control Bits M[2:0]
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1308ECM+T | IC ADC 12BIT 8CH 4MSPS 48LQFP |
| MAX1320ECM+T | IC ADC 14BIT 8CH 2MSPS 48LQFP |
| MAX132EWG+T | IC ADC 18BIT SERIAL 24-SOIC |
| MAX135EPI+ | IC ADC 15BIT PARALLEL 28-DIP |
| MAX1361MEUB+T | IC SYSTEM MON 10BIT 4CH 10-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1303BEUP+ | 功能描述:模數轉換器 - ADC 16-Bit 4Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1303BEUP+T | 功能描述:模數轉換器 - ADC 16-Bit 4Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1303BEUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX13041ASD/V+ | 功能描述:CAN 接口集成電路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13041ASD/V+T | 功能描述:CAN 接口集成電路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。