- 您現在的位置：買賣IC網 > PDF目錄180226 > M50FLW080AN5T (STMICROELECTRONICS) 1M X 8 FLASH 3V PROM, 11 ns, PDSO40 PDF資料下載
參數資料
| 型號： | M50FLW080AN5T |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 1M X 8 FLASH 3V PROM, 11 ns, PDSO40 |
| 封裝： | 10 X 20 MM, PLASTIC, TSOP-40 |
| 文件頁數： | 16/53頁 |
| 文件大小： | 945K |
| 代理商： | M50FLW080AN5T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
23/53
M50FLW080A, M50FLW080B
When the Program Suspend Status bit is ‘0’, the
Program/Erase Controller is active, or has com-
pleted its operation. When the bit is ‘1’, a Program/
Erase Suspend command has been issued and
the memory is waiting for a Program/Erase Re-
sume command.
When a Program/Erase Resume command is is-
sued, the Program Suspend Status bit returns to
‘0’.
Block/Sector Protection Status (Bit SR1). The
Block/Sector Protection Status bit can be used to
identify if the Program or Erase operation has tried
to modify the contents of a protected block or sec-
tor. When the Block/Sector Protection Status bit is
reset to ‘0’, no Program or Erase operations have
been attempted on protected blocks or sectors
since the last Clear Status Register command or
hardware reset. When the Block/Sector Protection
Status bit is ‘1’, a Program or Erase operation has
been attempted on a protected block or sector.
Once it is set to ‘1’, the Block/Sector Protection
Status bit can only be reset to ‘0’ by a Clear Status
Register command or by a hardware reset. If it is
set to ‘1’, it should be reset before a new Program
or Erase command is issued, otherwise the new
command will appear to have failed, too.
Using the A/A Mux Interface, the Block/Sector Pro-
tection Status bit is always ‘0’.
Reserved (Bit SR0). Bit 0 of the Status Register
is reserved. Its value should be masked.
Table 14. Status Register Bits
Note: 1. For Program operations during Erase Suspend, the SR6 bit is ‘1’, otherwise the SR6 bit is ‘0’.
Operation
SR7
SR6
SR5
SR4
SR3
SR2
SR1
Program active
‘0’
X(1)
‘0’
Program suspended
‘1
X(1)
‘0’
‘1’
‘0’
Program completed successfully
‘1’
X(1)
‘0’
Program failure due to VPP Error
‘1’
X(1)
‘0’
‘1’
‘0’
Program failure due to Block/Sector Protection
(FWH/LPC Interface only)
‘1’
X(1)
‘0’
‘1’
‘0’
‘1’
Program failure due to cell failure
‘1’
X(1)
‘0’
‘1’
‘0’
Erase active
‘0’
Erase suspended
‘1’
‘0’
Erase completed successfully
‘1’
‘0’
Erase failure due to VPP Error
‘1’
‘0’
‘1’
‘0’
‘1’
‘0’
Erase failure due to Block/Sector Protection
(FWH/LPC Interface only)
‘1’
‘0’
‘1’
‘0’
‘1’
Erase failure due to failed cell(s) in block or sector
‘1’
‘0’
‘1’
‘0’
發布緊急采購，3分鐘左右您將得到回復。