- 您現在的位置：買賣IC網 > PDF目錄45050 > M41T93ZQA6F (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PQCC16 PDF資料下載
參數資料
| 型號： | M41T93ZQA6F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PQCC16 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, QFN-16 |
| 文件頁數： | 5/49頁 |
| 文件大?。?/td> | 719K |
| 代理商： | M41T93ZQA6F |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
M41T93
Operation
Doc ID 12615 Rev 5
2.1
SPI bus characteristics
The serial peripheral interface (SPI) bus is intended for synchronous communication
between different ICs. It consists of four signal lines: serial data input (SDI), serial data
output (SDO), serial clock (SCL) and a chip enable (E).
By definition a device that gives out a message is called “transmitter,” the receiving device
that gets the message is called “receiver.” The device that controls the message is called
“master.” The devices that are controlled by the master are called “slaves.”
The E input is used to initiate and terminate a data transfer. The SCL input is used to
synchronize data transfer between the master (micro) and the slave (M41T93) device.
The SCL input, which is generated by the microcontroller, is active only during address and
data transfer to any device on the SPI bus (see Figure 5 on page 10).
The M41T93 can be driven by a microcontroller with its SPI peripheral running in only mode
0: (CPOL, CPHA) = (0,0).
For this mode, input data (SDI) is latched in by the low-to-high transition of clock SCL, and
output data (SDO) is shifted out on the high-to-low transition of SCL (see Table 2 and
There is one clock for each bit transferred. Address and data bits are transferred in groups
of eight bits. Due to memory size the second most significant address bit is a “don’t care”
(address bit 6).
2.2
READ and WRITE cycles
Address and data are shifted MSB first into the serial data input (SDI) and out of the serial
data output (SDO). Any data transfer considers the first bit to define whether a READ or
WRITE will occur. This is followed by seven bits defining the address to be read or written.
Data is transferred out of the SDO for a READ operation and into the SDI for a WRITE
operation. The address is always the second through the eighth bit written after the enable
(E) pin goes low. If the first bit is a '1,' one or more WRITE cycles will occur. If the first bit is a
'0,' one or more READ cycles will occur (see Figure 7 and Figure 8 on page 14).
Data transfers can occur one byte at a time or in multiple byte burst mode, during which the
address pointer will be automatically incremented. For a single byte transfer, one byte is
read or written and then E is driven high. For a multiple byte transfer all that is required is
that E continue to remain low. Under this condition, the address pointer will continue to
increment as stated previously. Incrementing will continue until the device is deselected by
taking E high. The address will wrap to 00h after incrementing to 3Fh.
The system-to-user transfer of clock data will be halted whenever the address being read is
a clock address (00h to 07h). Although the clock continues to maintain the correct time, this
will prevent updates of time and date during either a READ or WRITE of these address
locations by the user. The update will resume either due to a deselect condition or when the
pointer increments to an non-clock or RAM address (08h to 1Fh).
Note:
This is true both in READ and WRITE mode.
相關PDF資料 |
PDF描述 |
|---|---|
| M41T93RQA6F | 1 TIMER(S), REAL TIME CLOCK, PQCC16 |
| M41T93SQA6F | 1 TIMER(S), REAL TIME CLOCK, PQCC16 |
| M43C505-XXX-DIT | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC |
| M43C505-XXX-Q44 | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44 |
| M44C090-XXX-FL16 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T94 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Bit 64 bit x8 SERIAL RTC SPI SRAM |
| M41T94_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial Real Time Clock with 44Bytes NVRAM and Reset |
| M41T94_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock with 44 bytes NVRAM and reset |
| M41T94_09 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock with 44 bytes NVRAM and reset |
| M41T94MH | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Bit 64 bit x8 SERIAL RTC SPI SRAM |
發布緊急采購，3分鐘左右您將得到回復。