- 您現在的位置：買賣IC網 > PDF目錄299434 > M39208-15WNB1 (STMICROELECTRONICS) 256K X 8 FLASH 2.7V PROM, 150 ns, PDSO32 PDF資料下載
參數資料
| 型號： | M39208-15WNB1 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 256K X 8 FLASH 2.7V PROM, 150 ns, PDSO32 |
| 封裝： | 8 X 14 MM, PLASTIC, TSOP-32 |
| 文件頁數： | 7/30頁 |
| 文件大?。?/td> | 218K |
| 代理商： | M39208-15WNB1 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Flash Sector Unprotection. Flash sectors can be
unprotected to allow updating of their contents.
Note that the Sector Unprotection unprotects all
sectors (sector 0 up to sector 7).
Flash Sector Unprotection is activated with a spe-
cific sequence of levels applied on EF, EE, G, A0,
A1, A6, A9, A12 and A15; this sequence includes a
verification of the Protection status on DQ0-DQ7
as shown in Figure 9 and Table 9.
This allows a guarantee of the retention of the
Protection status.
Remarks:
– The Verify operation is a read with a simulated
worst case conditions. This allows a guarantee
of the retention of the Protection status
– During the application life, the Sector protection
status can be accessed with a regular Read
instruction without "high voltage" VID on A9. This
instruction is detailed in Table 4.
Reset Instruction. The Reset instruction resets
the device internal logic in a few
s. Reset is an
instruction of either one write operation or three
write operations (refer to Table 4).
Supply Rails. Normal precautions must be taken
for supply voltage decoupling, each device in a
system should have the VCC rail decoupled with a
0.1
F capacitor close to the VCC and VSS pins. The
printed circuit board trace width should be sufficient
to carry the VCC program and erase currents re-
quired.
AI01950
1.5V
2.4V
0.45V
Figure 10. AC Testing Input Output Waveform
AI02596B
VCC
CL = 30pF
CL includes JIG capacitance
VOUT = 1.5V when the DEVICE
UNDER TEST is in the
Hi-Z output state.
DEVICE
UNDER
TEST
IOL
IOH
Figure 11. Output AC Testing Load Circuit
Symbol
Parameter
Test Condition
Min
Max
Unit
CIN
Input Capacitance
VIN = 0V
6
pF
COUT
Output Capacitance
VOUT = 0V
12
pF
Note: 1. Sampled only, not 100% tested.
Table 11. Capacitance (1) (TA = 25
°C, f = 1 MHz )
Input Rise and Fall Times
≤ 10ns
Input Pulse Voltages
0.45V to 2.4V
Input Timing Ref. Voltages
0.8V and 2V
Output Timing Ref. Voltages
1.5V
Table 10. AC Measurement Conditions
15/30
M39208
相關PDF資料 |
PDF描述 |
|---|---|
| M3933/10-17N | 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| M3933/25-65N | 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| M3933/10-16S | 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| M3933/14-23S | 0 MHz - 12400 MHz RF/MICROWAVE FIXED ATTENUATOR |
| M3933/25-31S | 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M39208-15WNB1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single Chip 2 Mbit Flash and 64 Kbit Parallel EEPROM Memory |
| M39208-15WNB5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single Chip 2 Mbit Flash and 64 Kbit Parallel EEPROM Memory |
| M39208-15WNB6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single Chip 2 Mbit Flash and 64 Kbit Parallel EEPROM Memory |
| M39208NA | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single Chip 2 Mbit Flash and 64 Kbit Parallel EEPROM Memory |
| M39208NB | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single Chip 2 Mbit Flash and 64 Kbit Parallel EEPROM Memory |
發布緊急采購，3分鐘左右您將得到回復。