- 您現在的位置：買賣IC網 > PDF目錄45036 > M37641M8-XXXFP 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37641M8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 87/136頁 |
| 文件大小： | 1672K |
| 代理商： | M37641M8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁當前第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
54
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
[USB Endpoint x (x = 1 to 4) IN Control Register] IN_CSR
This register contains the control and status information of the re-
spective IN Endpoints 1 to 4.
Set the IN_PKT_RDY bit to “1” after the data packet has been
written to the IN FIFO. This bit is cleared to “0” when the data
transfer is completed. In a bulk IN transfer, this bit is cleared when
an ACK signal is received from the host. If an ACK signal is not re-
ceived, this bit (and the TX_NOT_EMPTY bit) remains as “1”. This
same data packet is sent after the next IN token is received. The
FLUSH bit is for flushing the data in the IN FIFO.
USB endpoint x IN control register (address 005916)
IN_CSR
INT_PKT_RDY bit (INXCSR0)
0: End of a data packet transmission (Note 1)
1: Write “1” at completion of writing a data packet into IN FIFO.
(Note 3)
UNDER_RUN flag (INXCSR1) (In isochronous data transfer)
0: No FIFO underrun (Note 2)
1: FIFO underrun occurred (Note 1) (USB overrun/underrun interrupt
status flag is set to “0”.)
SEND_STALL bit (INXCSR2) (Note 2)
0: Except the following condition
1: Transmitting STALL handshake signal
ISO/TOGGLE_INIT bit (INXCSR3) (Note 2)
0: Except the following condition
1: Initializing to endpoint used for isochronous transfer;
Initializing the data toggle sequence bit
INTPT bit (INXCSR4) (Note 2)
0: Except the following condition
1: Initializing to endpoint used for interrupt transfer, rate feedback
TX_NOT_EPT flag (INXCSR5) (Note 1)
0: Empty in IN FIFO
1: Full in IN FIFO
FLUSH bit (INXCSR6)
0: Except the following condition (Note 1)
1: Flush FIFO. (Note 2)
AUTO_SET bit (INXCSR7) (Note 2)
0: AUTO_SET disabled
1: AUTO_SET enabled
b0
b7
Notes 1: This bit is automatically set to “1” or cleared to “0”.
2: The user must program to “1” or “0”.
3: When AUTO_SET bit is “0”, the user must set to “1”. When AUTO_SET bit is “1”, this
bit is automatically set to “1”.
Fig. 47 Structure of USB endpoint x (x = 1 to 4) IN control register
相關PDF資料 |
PDF描述 |
|---|---|
| M37643M8-XXXFP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643F8HP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37700M2-XXXFP | 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37701M2-001SP | 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37641M8-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M376420RS | 制造商:OKI 功能描述:3764-20 NOTES |
| M3764-20RS | 制造商:OKI 功能描述:3764-20 NOTES 制造商: 功能描述:Dynamic RAM, Page Mode, 64K x 1, 16 Pin, Plastic, DIP 制造商:OK International 功能描述:Dynamic RAM, Page Mode, 64K x 1, 16 Pin, Plastic, DIP |
| M3-7643A-S | 制造商:Harris Corporation 功能描述: |
| M37643F8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。