- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542M4-XXXSP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP32 PDF資料下載
參數資料
| 型號： | M37542M4-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | 0.400 INCH, PLASTIC, SDIP-32 |
| 文件頁數： | 14/68頁 |
| 文件大?。?/td> | 1191K |
| 代理商： | M37542M4-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7542 Group
MITSUBISHI MICROCOMPUTERS
21
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
Interrupts
Interrupts occur by 18 different sources : 6 external sources, 11 in-
ternal sources and 1 software source.
Interrupt control
All interrupts except the BRK instruction interrupt have an interrupt
request bit and an interrupt enable bit, and they are controlled by
the interrupt disable flag. When the interrupt enable bit and the in-
terrupt request bit are set to “1” and the interrupt disable flag is set
to “0”, an interrupt is accepted.
The interrupt request bit can be cleared by program but not be set.
The interrupt enable bit can be set and cleared by program.
The reset and BRK instruction interrupt can never be disabled with
any flag or bit. All interrupts except these are disabled when the
interrupt disable flag is set.
When several interrupts occur at the same time, the interrupts are
received according to priority.
Interrupt operation
Upon acceptance of an interrupt the following operations are auto-
matically performed:
1. The processing being executed is stopped.
2. The contents of the program counter and processor status reg-
ister are automatically pushed onto the stack.
3. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
4. Concurrently with the push operation, the interrupt destination
address is read from the vector table into the program counter.
[Interrupt source set register] INTSET
When two interrupt sources are assigned to the same interrupt
vector, the valid/invalid of each interrupt is set by this register.
When both two interrupt sources are set to be valid, which inter-
rupt request occurs is confirmed by the next interrupt source
discrimination bit.
[Interrupt source discrimination register] INTDIS
When two interrupt sources are assigned to the same interrupt
vector, which interrupt source occurs is confirmed by this register.
If an interrupt request of a key-on wakeup, UART1 bus collision
detection, A-D conversion or timer 1 occurs, an interrupt discrimi-
nation bit is set to “1” regardless of valid/invalid state by the
interrupt source set register.
However, when the interrupt valid bit of an interrupt source set
register is “0” (invalid), the interrupt request bit of an interrupt con-
trol register is not set to “1.”
Moreover, since an interrupt discrimination bit is not automatically
cleared to “0” by interrupt, please clear it by program.
An interrupt discrimination bit can be cleared to “0” by program but
not be set to “1.”
[Interrupt edge selection register] INTEDGE
The valid edge of external interrupt INT0 and INT1 can be selected
by the interrupt edge selection bit, respectively.
For the external interrupt INT1, the external input pin P33/INT1 or
P36/INT1 can be selected by the INT1 input port selection bit.
However, since there is no P36/INT1 pin in the 32-pin version, se-
lect P33/INT1 pin. By the key-on wakeup selection bit, enable/
disable of a key-on wakeup of P00, P04, and P06 pins can be se-
lected, respectively.
s Notes on use
(1) When setting the followings, the interrupt request bit may be
set to “1”.
When setting external interrupt active edge
Related register:
Interrupt edge selection register (address 003A16)
Timer X mode register (address 002B16)
Capture mode register (address 002016)
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding interrupt enable bit to “0” (disabled).
Set the interrupt edge select bit (active edge switch bit, trigger
mode bit).
Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Set the corresponding interrupt enable bit to “1” (enabled).
(2) Use a LDM instruction to clear an interrupt discrimination bit.
LDM #$0n, $0Bn
Set the following values to “n”
“0”: an interrupt discrimination bit to clear
“1”: other interrupt discrimination bits
Ex.) When a key-on wakeup interrupt discrimination bit is
cleared;
LDM #00001110B and $0B.
相關PDF資料 |
PDF描述 |
|---|---|
| M37542F8SP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8VGP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
| M37542F8FP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDSO36 |
| M37542F8VFP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542M2T-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542RSS | 功能描述:DEV EMULATION EVA CHIP FOR M3754 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M37544 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37544G2AGP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 8KB ROM 5V 32LQFP - Trays |
| M37544G2AGP#U0 | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR |
| M37544G2ASP#U0 | 功能描述:MCU 2/5V 8K 32-SDIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。