- 您現在的位置：買賣IC網 > PDF目錄98006 > M37534E4GP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37534E4GP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 11/53頁 |
| 文件大?。?/td> | 680K |
| 代理商： | M37534E4GP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7534 Group
MITSUBISHI MICROCOMPUTERS
19
Timers
The 7534 Group has 3 timers: timer X, timer 1 and timer 2.
The division ratio of every timer and prescaler is 1/(n+1) provided
that the value of the timer latch or prescaler is n.
All the timers are down count timers. When a timer reaches “0”, an
underflow occurs at the next count pulse, and the corresponding timer
latch is reloaded into the timer. When a timer underflows, the inter-
rupt request bit corresponding to each timer is set to “1”.
qTimer 1, Timer 2
Prescaler 12 always counts f(XIN)/16. Timer 1 and timer 2 always
count the prescaler output and periodically sets the interrupt request
bit.
qTimer X
Timer X can be selected in one of 4 operating modes by setting the
timer X mode register.
Timer Mode
The timer counts the signal selected by the timer X count source
selection bit.
Pulse Output Mode
The timer counts the signal selected by the timer X count source
selection bit, and outputs a signal whose polarity is inverted each
time the timer value reaches “0”, from the CNTR0 pin.
When the CNTR0 active edge switch bit is “0”, the output of the
CNTR0 pin is started with an “H” output.
At “1”, this output is started with an “L” output. When using a timer in
this mode, set the port P14 direction register to output mode.
Event Counter Mode
The operation in the event counter mode is the same as that in the
timer mode except that the timer counts the input signal from the
CNTR0 pin.
When the CNTR0 active edge switch bit is “0”, the timer counts
the rising edge of the CNTR0 pin. When this bit is “1”, the timer
counts the falling edge of the CNTR0 pin.
Pulse Width Measurement Mode
When the CNTR0 active edge switch bit is “0”, the timer counts the
signal selected by the timer X count source selection bit while the
CNTR0 pin is “H”. When this bit is “1”, the timer counts the signal
while the CNTR0 pin is “L”.
In any mode, the timer count can be stopped by setting the timer X
count stop bit to “1”. Each time the timer overflows, the interrupt
request bit is set.
Fig. 19 Structure of timer X mode register
Fig. 20 Timer count source set register
Timer X mode register
(TM : Address 002B 16)
CNTR0 active edge switch bit
0 : Interrupt at falling edge
Count at rising edge
(in event counter mode)
1 : Interrupt at rising edge
Count at falling edge
(in event counter mode)
Timer X operating mode bits
b1 b0
0
0 : Timer mode
0
1 : Pulse output mode
1
0 : Event counter mode
1
1 : Pulse width measurement mode
Not used (return “0” when read)
Timer X count stop bit
0 : Count start
1 : Count stop
b7
b0
Timer count source set register
(TCSS : Address 002E 16)
b7
b0
Timer X count source selection bit (Note)
0 : f(XIN)/16
1 : f(XIN)/2
Not used (return “0” when read)
Note : To switch the timer X count source selection bit ,
stop the timer X count operation.
相關PDF資料 |
PDF描述 |
|---|---|
| M37548G3FP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
| M37548G1FP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
| M37548G2-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
| M37640E8-XXXFP | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP80 |
| M37702S1ABFP | 16-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37534E4GP#U1 | 功能描述:MCU 4/5V 8K PB-FREE 32-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M37534E8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534E8SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。