參數資料
型號： M37532E8FP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36
封裝： 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-36
文件頁數： 15/51頁
文件大?。?/td> 736K
代理商： M37532E8FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7532 Group
MITSUBISHI MICROCOMPUTERS
21
[Serial I/O1 control register] SIO1CON
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[UART control register] UARTCON
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set the
data format of an data transfer. One bit in this register (bit 4) is al-
ways valid and sets the output structure of the P11/TxD pin.
[UART status register] UARTSTS
The read-only UART status register consists of seven flags (bits 0 to
6) which indicate the operating status of the UART function and vari-
ous errors. This register functions as the UART status register
(UARTSTS) when selecting the UART.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer is read.
If there is an error, it is detected at the same time that data is trans-
ferred from the receive shift register to the receive buffer, and the
receive buffer full flag is set. A write to the UART status register clears
all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively).
Writing “0” to the serial I/O1 mode selection bits MOD1 and MOD0
(bit 7 and 6 of the Serial I/O1 control register ) also clears all the
status flags, including the error flags.
All bits of the serial I/O1 status register are initialized to “8116” at
reset, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the continuous transmit valid bit (bit 2)
becomes “1”.
[Transmit/Receive buffer register] TB/RB
The transmit buffer and the receive buffer are located at the same
address. The transmit buffer is write-only and the receive buffer is
read-only. If a character bit length is 7-bit, the MSB of data stored in
the receive buffer is “0”.
Fig. 23 Continuous transmission operation of UART serial I/O
[Baud Rate Generator] BRG
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
TSC=0
TBE=1
TBE=0
ST
D0
D1
SP
D0
D1
ST
SP
ST
1 : When the serial I/O1 mode selection bits (b7, b6) is “10”, the transmit enable bit is “1”, and continuous transmit valid bit is “1”, writing on the
transmit buffer initiates continuous transmission of the same data.
2 : Select 0 for continuous transmit valid bit to stop continuous transmission.
The TXD pin will stop at high level after completing transmission of 1 byte.
3 : If the transmit buffer contents are rewritten during a continuous transmission, transmission of the rewritten data will be started after
completing transmission of 1 byte.
Notes
1 Start Bit
7 or 8 Data Bit
1 or 0 Parity Bit
1 or 2 Stop Bit
Transmit/Receive Clock
Transmit Buffer Register
Write Signal
Serial Output TXD
相關PDF資料
PDF描述
M37532M4-XXXGP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
M37536M4-XXXSP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP42
M37536E8SP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDIP42
M37540E8FP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO36
M37540M4T-XXXGP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
M37532M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-A17GP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-XXXFP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
M37532M4-XXXGP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
M37532RSS 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*