參數資料
型號: M37531M4T-XXXFP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36
封裝: 0.450 INCH, PLASTIC, SSOP-36
文件頁數: 154/215頁
文件大?。?/td> 1365K
代理商: M37531M4T-XXXFP
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁當前第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁
7531 Group User’s Manual
1-29
HARDWARE
Serial I/O2 operation
By writing to the serial I/O2 register (address 003116) the serial I/O2
counter is set to “7”.
After writing, the SDATA pin outputs data every time the transfer clock
shifts from a high to a low level. And, as the transfer clock shifts from
a low to a high, the SDATA pin reads data, and at the same time the
contents of the serial I/O2 register are shifted by 1 bit.
When the internal clock is selected as the transfer clock source, the
following operations execute as the transfer clock counts up to 8.
Serial I/O2 counter is cleared to “0”.
Transfer clock stops at an “H” level.
Interrupt request bit is set.
Shift completion flag is set.
Also, the SDATA pin is in a high impedance state after the data trans-
fer is complete (refer to figure 31).
When the external clock is selected as the transfer clock source, the
interrupt request bit is set as the transfer clock counts up to 8, but
external control of the clock is required since it does not stop. Notice
that the SDATA pin is not in a high impedance state on the completion
of data transfer.
Fig. 31 Serial I/O2 timing (LSB first)
FUNCTIONAL DESCRIPTION
D0
Synchronous clock
Serial I/O2 register
write signal
Transfer clock
(Note)
SDATA at serial I/O2
input receive
SDATA at serial I/O2
output transmit
Serial I/O2 interrupt request bit set
D1
D2
D3
D4
D5
D6
D7
Note : When the internal clock is selected as the transfer and the direction register of P1 3/SDATA pin is set to the input mode,
the SDATA pin is in a high impedance state after the data transfer is completed.
相關PDF資料
PDF描述
M37531M4T-XXXGP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32
M37531E4V-XXXGP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32
M37531E8SP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32
M37531E8FP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO36
M37531E4T-XXXGP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
M37531RSS 制造商:Mitsubishi Electric 功能描述:
M37531T-ADS 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Temporary Target Board
M37532E8FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-A17GP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER