- 您現在的位置：買賣IC網 > PDF目錄384636 > M37531 (Mitsubishi Electric Corporation) Single Chip 8 Bits CMOS Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M37531 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| 中文描述： | 單芯片的CMOS 8位單片機（8位單片機） |
| 文件頁數： | 25/64頁 |
| 文件大?。?/td> | 631K |
| 代理商： | M37531 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7531 Group
MITSUBISHI MICROCOMPUTERS
25
Serial I/O2 operation
By writing to the serial I/O2 register (address 0031
16
) the serial I/O2
counter is set to
“
7
”
.
After writing, the S
DATA
pin outputs data every time the transfer clock
shifts from a high to a low level. And, as the transfer clock shifts from
a low to a high, the S
DATA
pin reads data, and at the same time the
contents of the serial I/O2 register are shifted by 1 bit.
When the internal clock is selected as the transfer clock source, the
following operations execute as the transfer clock counts up to 8.
Serial I/O2 counter is cleared to
“
0
”
.
Transfer clock stops at an
“
H
”
level.
Interrupt request bit is set.
Shift completion flag is set.
Also, the S
DATA
pin is in a high impedance state after the data trans-
fer is complete (refer to Figure 29).
When the external clock is selected as the transfer clock source, the
interrupt request bit is set as the transfer clock counts up to 8, but
external control of the clock is required since it does not stop. Notice
that the S
DATA
pin is not in a high impedance state on the completion
of data transfer.
Fig. 29 Serial I/O2 timing (LSB first)
D
0
Synchronous clock
Serial I/O2 register
write signal
Transfer clock
(Note)
S
DATA
at serial I/O2
input receive
S
DATA
at serial I/O2
output transmit
Serial I/O2 interrupt request bit set
D
1
D
2
D
3
D
4
D
5
D
6
D
7
Note
:
When the internal clock is selected as the transfer and the direction register of P1
3
/S
DATA
pin is set to the input mode,
the S
DATA
pin is in a high impedance state after the data transfer is completed.
相關PDF資料 |
PDF描述 |
|---|---|
| M37534 | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| M37700 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
| M37721 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
| M37733MHB | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37735S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37531E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4FP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MITSUBISHI 8 BIT OTP MCU |
| M37531E4GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E8FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。