- 您現在的位置：買賣IC網 > PDF目錄45033 > M37517F8HP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M37517F8HP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 46/98頁 |
| 文件大?。?/td> | 886K |
| 代理商： | M37517F8HP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
Rev.1.01
Aug 02, 2004
page 50 of 96
7517 Group
CLOCK GENERATING CIRCUIT
The 7517 group has four built-in oscillation circuits: high-speed
on-chip oscillation circuit, an oscillation circuit can be formed by
connecting a resonator between XIN and XOUT, resonator between
XCIN and XCOUT, and a 32 kHz RC oscillation circuit can be formed
by connecting capacitor and resistor. The oscillation source (high-
speed on-chip oscillation or XIN-XOUT oscillation) can be
controlled by setting the clock source switch bit (CPU mode regis-
ter) and high-speed on-chip oscillation stop bit (MISRG2) and XIN
switching inhibit bit (MISRG2). Immediately after power on, only
the high-speed on-chip oscillation circuit starts oscillation. In case
of using XIN-XOUT oscillation circuit, change the clock source
switch bit after start the XIN-XOUT oscillation setting the main clock
(XIN-XOUT) stop bit (CPU mode register).
When not using XIN-XOUT oscillation circuit, XIN pin and XOUT pin
must be open.
Setting the XIN switching inhibit bit “1” (disable switch to XIN), the
clock source switch bit become invalid, and XIN-XOUT oscillation
circuit becomes disabled since. When this bit is set to “1”, it can-
not be rewritten to “0” by program.
Setting the port Xc switch bit (CPU mode register) “1”, 32 kHz RC
oscillation circuit or XCIN-XCOUT oscillation circuit starts oscilla-
tion. The selection of 32 kHz RC oscillation circuit or XcIN-XCOUT
oscillation circuit is selected by 32 kHz RC oscillation enable bit
(MISRG2).
In case of using external resonator, connect resonator to XIN pin
and XOUT pin (XCIN pin and XCOUT pin). Use the circuit constants
in accordance with the resonator manufacturer’s recommended
values. No external resistor is needed between XIN and XOUT
since a feed-back resistor exists on-chip. However, an external
feed-back resistor is needed between XCIN and XCOUT.
Immediately after power on, XCIN and XCOUT pins function as I/O
ports.
Frequency Control
(1) Middle-speed mode
The internal clock
φ is the frequency of high-speed on-chip oscilla-
tion clock or XIN divided by 8. After reset, this mode is selected.
(2) High-speed mode
The internal clock
φ is half the frequency of high-speed on-chip
oscillation clock or XIN.
(3) Low-speed mode
The internal clock
φ is half the frequency of XCIN.
sNote
If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and XCIN oscillations. The sufficient time
is required for the sub-clock to stabilize, especially immediately af-
ter power on and at returning from the stop mode. When switching
the mode between middle/high-speed and low-speed, set the fre-
quency on condition that f(XIN) > 3f(XCIN).
(4) Low power dissipation mode
The low power consumption operation can be realized by stopping
the main clock XIN or high-speed on-chip oscillation in low-speed
mode. To stop the main clock, set the main clock stop bit (bit 5 of
CPU mode register) or the high-speed on-chip oscillation stop bit
(bit 2 of MISRG2) to “1”. When the main clock XIN is restarted (by
setting the main clock stop bit to “0”), set sufficient time for oscilla-
tion to stabilize.
The sub-clock XCIN-XCOUT oscillating circuit can not directly input
clocks that are generated externally. Accordingly, make sure to
cause an external resonator to oscillate.
32kHz RC oscillation circuit
Setting the port Xc switch bit “1” after setting the 32 kHz RC oscil-
lation enable bit “1”, the built-in 32 kHz RC oscillation circuit starts
oscillation. In case of using 32 kHz RC oscillation circuit, connect
82 k
resistor between XCIN-XCOUT, and connect 120 pF capaci-
tor between XCIN and GND.
Setting appropriate value to the 32 kHz oscillation circuit control
registers 0,1 it is possible to adjust the frequency error cause by
evenness of resistor and capacitor value .
The resistor ladder divided by 512 adjusts the frequency, and it
makes possible about 50 Hz step adjustment.
The theoretical frequency is calculated as follow.
1
f32CR=
2CRln(1+2R1/R2)
相關PDF資料 |
PDF描述 |
|---|---|
| M37524E4-XXXSP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP64 |
| M37531E4V-XXXGP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37531M4T-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37531M4V-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37531E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37530T-PTC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 42-pin 1.778mm-pitch SDIP to a 40-pin Narrow-pitch Connector (for 7531, 7540, 7542 and 7544 Groups) |
| M37530T-PTCB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 40-pin Narrow-pitch Connector to 32-pin 0.8mm-pitch LQFP (for 7531, 7532, 7534, 7540, 7542 and 7544 Groups) |
| M37530T-PTCC | 功能描述:DEV 42-PIN RSS/MCU TO 32-PIN 1.7 RoHS:否 類別:編程器，開發(fā)系統(tǒng) >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37531E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4FP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MITSUBISHI 8 BIT OTP MCU |
發(fā)布緊急采購，3分鐘左右您將得到回復。