參數資料
型號: M34571G6FP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
封裝: 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24
文件頁數: 82/126頁
文件大?。?/td> 1776K
代理商: M34571G6FP
Rev.1.02
May 25, 2007
Page 59 of 124
REJ03B0179-0102
4571 Group
NOTES ON NOISE
Countermeasures against noise are described below.
The following countermeasures are effective against noise in
theory, however, it is necessary not only to take measures as
follows but to evaluate before actual use.
1. Shortest wiring length
(1) Wiring for RESET pin
Make the length of wiring which is connected to the RESET pin
as short as possible. Especially, connect a capacitor across the
RESET pin and the VSS pin with the shortest possible wiring.
<Reason>
In order to reset a microcomputer correctly, 1 machine cycle or
more of the width of a pulse input into the RESET pin is
required.
If noise having a shorter pulse width than this is input to the
RESET input pin, the reset is released before the internal state of
the microcomputer is completely initialized.
This may cause a program runaway.
Fig 62. Wiring for the RESET pin
(2) Wiring for clock input/output pins
Make the length of wiring which is connected to clock I/O pins
as short as possible.
Make the length of wiring across the grounding lead of a
capacitor which is connected to an oscillator and the VSS pin
of a microcomputer as short as possible.
Separate the VSS pattern only for oscillation from other VSS
patterns.
<Reason>
If noise enters clock I/O pins, clock waveforms may be deformed.
This may cause a program failure or program runaway. Also, if a
potential difference is caused by the noise between the VSS level
of a microcomputer and the VSS level of an oscillator, the correct
clock will not be input in the microcomputer.
Fig 63. Wiring for clock I/O pins
(3) Port K Wiring
Do not leave port K open. Always connect it to the VDD pin or
VSS pin using the thickest wire at the shortest distance.
When port K is used for key matrix, connect it to the VDD pin
through a pull-up resistor.
In that case too, place a pull-up resistor close to port K and
connect it to port K or the VDD pin using the thickest wire at the
shortest distance as above.
<Reason>
Port K is also used as the power source input pin (VPP pin) for
the built-in QzROM.
When programming to the QzROM, the impedance of port K is
low so that the electric writing current will flow into the
QzROM. This allows noise to enter easily. If noise enters from
port K, abnormal instruction codes or data are read from the
QzROM, which may cause a program runaway.
Fig 64.
Wiring for port K
RESET
Reset
circuit
Noise
VSS
N.G.
Reset
circuit
VSS
RESET
VSS
O.K.
Noise
XIN
XOUT
VSS
N.G.
XIN
XOUT
VSS
O.K.
VDD
VSS
K
Shortest
distance
(Note)
Note: This indicates pin.
VDD
VSS
K
Shortest
distance
(Note)
VDD
VSS
K
Shortest
distance
Shortest
distance
A pull-up resistor
(Note)
相關PDF資料
PDF描述
M34584EDFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42
M35047-XXXSP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20
M35047-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35048-001FP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35049-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
相關代理商/技術參數
參數描述
M34571G6-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571GD 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571GDFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571GD-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3458 功能描述:電纜固定件和配件 RLTCG 3/8 NPT BLACK NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: