- 您現在的位置：買賣IC網 > PDF目錄45009 > M30102F3TFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M30102F3TFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 153/164頁 |
| 文件大?。?/td> | 3302K |
| 代理商： | M30102F3TFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁當前第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁
Under
development
Tentative Specifications REV.E1
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30100/M30102 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Timer Z
88
(3) Programmable one-shot generation mode
_______
In this mode, upon software command or external trigger input (input to the INT0 pin), the microcom-
puter outputs the one-shot pulse from the TZOUT pin. (See Table 1.14.12) When a trigger occurs, the
timer starts operating from the point only once for a given period equal to the set value of the Timer Z
primary. Timer Z secondary is unused in this mode. Figure 1.14.27 shows the Timer Y, Z mode
register and Timer Y, Z waveform output control register in this mode. Figure 1.14.28 shows the Timer
Z operation example in this mode.
Item
Specification
Count source
f1, f8, Timer Y underflow, fC32
Count operation
Downcounts the set value of Timer Z primary
When the timer underflows, it reloads the contents of reload register before stopping
counting.
When a counting stops, the timer reloads the contents of the reload register before it
stops.
Divide ratio
1/(n+1)/(m+1)
n : Set value of Prescaler Z, m: Set value of Timer Z primary
Count start condition
Timer Z one-shot start bit is set (=1) (Note 1)
_______
Valid trigger is input to INT0 pin (Note 2)
Count stop condition
When reloading is completed after count value was set to "0016"
When Count start flag is reset (=0) (Note 3)
Timer Z one-shot start bit is reset (=0) (Note 3)
Interrupt request generation timing When count value becomes "0016"
TZOUT pin function
Pulse output
_______
INT0 pin function
Programmable I/O port, external interrupt input pin, or external trigger input pin
Read from timer
Count value can be read out by reading Timer Z primary register.
Same applies to Prescaler Z register.
Write to timer
When a value is written to Timer Z primary register, it is written to only reload register.
Same applies to Prescaler Z register. (Note 4)
Select function
Output level latch select function
The output level of one-shot pulse waveform is selectable.
_______
INT0 pin one-shot trigger control function and polarity select function
_______
The trigger input from the INT0 pin can be set to valid or invalid. Also, the valid trigger's
polarity can be chosen to be the rising edge, falling edge, or rising and falling both
edges.
Waveform extend function
The one-shot pulse waveform can be extended 0.5 cycles of the count source (Note 5)
Frequency when waveform extended: 2/(n+1)/(2x(m+1)+TZPUM0)
n: set value of Prescaler Z, m: set value of Timer Z primary
TZPUM0: Timer Z primary waveform extension control bit
Note 1: Count start flag must have been set to "1".
_______
Note 2: Count start flag must have been set to "1", INT0 input enable bit [INT0EN] to "1", and INT0 one-shot trigger
control bit to "1".
Note 3: When the count is stopped by writing 0 to the count start flag or Timer Z one-shot start bit, the Timer Z interrupt
request flag becomes "1" and an interrupt may occur. Thus, interrupts must be disabled before the count is
stopped. Furthermore, set the Timer Z interrupt request bit to "0" before starting counting again.
Note 4: Each set value becomes effective by writing to the Timer Z primary register. And the set values are reflected
collectively beginning with the next one-shot pulse after writing to the Timer Z primary.
Note 5: When using the waveform extend function, the Prescaler Z register must be set to "0016".
When selecting Timer Y underflow and f1 for the count source, the waveform extend function cannot be used.
Table 1.14.12. Specifications of programmable one-shot generating mode
相關PDF資料 |
PDF描述 |
|---|---|
| M30102M6T-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
| M30100M3T-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32 |
| M30100M3-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32 |
| M30100F3FP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32 |
| M30102M3T-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30102T-PTC | 制造商:Renesas Electronics Corporation 功能描述:DEV 48PIN .5MM QFP CNVTR FOR M30100T-PRB - Bulk |
| M30-1050046 | 功能描述:集管和線殼 FML CRIMP CONTACT 1.25MM,AWG 26-30, RL RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| M30-1060046 | 功能描述:集管和線殼 FML CRIMP CONTACT 1.25MM,AWG 26-30,LSE RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| M3010A | 制造商:Honeywell Sensing and Control 功能描述:GENERAL MARKET VRS |
| M3010A25 | 制造商:Honeywell Sensing and Control 功能描述:GENERAL MARKET VRS |
發布緊急采購，3分鐘左右您將得到回復。