參數資料
型號： M30100M3-XXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32
封裝： PLASTIC, LQFP-32
文件頁數： 136/163頁
文件大?。?/td> 2767K
代理商： M30100M3-XXXFP
Under
development
Tentative Specifications REV.E1
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30100/M30102 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Timer Y
74
(1) Timer mode
In this mode, the timer counts an internally generated count source. (See Table 1.14.8) The Timer Y
secondary is unused in this mode. Figure 1.14.17 shows the Timer Y, Z mode register and Timer Y, Z
waveform output control register in timer mode.
Item
Specification
Count source
f1, f8, ring oscillator output, fC32
Count operation
Down count
When the timer underflows, it reloads the reload register contents before continuing
counting (When the Timer Y underflows, the contents of the Timer Y primary reload
register is reloaded.)
When a counting stops, the timer reloads the content of the reload register before it
stops.
Divide ratio
1/(n+1)/(m+1) n : Set value of Prescaler Y, m: Set value of Timer Y primary
Count start condition
Count start flag is set (=1)
Count stop condition
Count start flag is reset (=0) (Note 1)
Interrupt request generation timing When Timer Y underflows
TYOUT pin function
Programmable I/O port
Read from timer
Count value can be read out by reading Timer Y primary register.
Same applies to Prescaler Y register.
Write to timer
When a value is written to Timer Y Primary register, it is written to both reload register
and counter or written to only reload register. Selected by software.
Same applies to Prescaler Y register.
Select function
Timer Y write control function
When a value is written to Timer Y Primary register, it can be selected that the value is
written to both reload register and counter or written to only reload register.
Same applies to Prescaler Z register. (Note 2)
Note 1: When the count is stopped, the Timer Y interrupt request flag becomes "1" and an interrupt may occur. Thus,
interrupts must be disabled before the count is stopped. Furthermore, set the Timer Y interrupt request flag to "0"
before starting counting again.
Note 2: If writing to the Timer Y or prescaler Y under the following conditions being filled at the same time the Timer Y
interrupt request flag becomes "1" and an interrupt occurs.
<Conditions>
Timer Y write control bit (bit 2 of address 0080) is "0" (write to timer and reload register simultaneously)
Timer Y count start flag (bit 3 of address 0080) is "1" (count start)
To write to the Timer Y or prescaler Y in the above state, disable interrupts before writing.
Table 1.14.8. Specifications of timer mode
相關PDF資料
PDF描述
M30100F3TFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32
M30102M2T-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
M30100M2T-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32
M30102M6T-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
M30102M3-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
相關代理商/技術參數
參數描述
M30100T3-RPD-E 制造商:Renesas Electronics Corporation 功能描述:DEV EMULATOR POD M16C/10 SERIES - Bulk
M30100T-PTC 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 32-pin 0.8mm-pitch QFP for M30100T-PRB (for M16C/10 Group M30100)
M30-1010046 功能描述:集管和線殼 1.25MM FEMALE CRIMP TIN PK OF 105 RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector
M3010102636207.32LLZZ 制造商:3M Electronic Products Division 功能描述:QUOTE # V05-0068
M30102 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*