參數資料
型號： M29W800FB9N3F
廠商： NUMONYX
元件分類： PROM
英文描述： 512K X 16 FLASH 3V PROM, 90 ns, PDSO48
封裝： 12 X 20 MM, ROHS COMPLIANT, PLASTIC, TSOP-48
文件頁數： 37/49頁
文件大?。?/td> 936K
代理商： M29W800FB9N3F
Block protection
M29W800FT, M29W800FB
Appendix C
Block protection
Block protection can be used to prevent any operation from modifying the data stored in the
Flash. Each block can be protected individually. Once protected, program and erase
operations on the block fail to change the data.
There are three techniques that can be used to control block protection, these are the
programmer technique, the in-system technique and temporary unprotection. Temporary
unprotection is controlled by the Reset/Block Temporary Unprotection pin, RP; this is
Unlike the command interface of the program/erase controller, the techniques for protecting
and unprotecting blocks change between different Flash memory suppliers. For example,
the techniques for AMD parts will not work on Numonyx parts. Care should be taken when
changing drivers for one part to work on another.
C.1
Programmer technique
The programmer technique uses high (VID) voltage levels on some of the bus pins. These
cannot be achieved using a standard microprocessor bus, therefore the technique is
recommended only for use in programming equipment.
To protect a block follow the flowchart in Figure 15: Programmer equipment block protect
flowchart, To unprotect the whole chip it is necessary to protect all of the blocks first, then all
blocks can be unprotected at the same time. To unprotect the chip follow Figure 16:
operations, BYTE = VIH or VIL, gives a summary of each operation.
The timing on these flowcharts is critical. Care should be taken to ensure that, where a
pause is specified, it is followed as closely as possible. Do not abort the procedure before
reaching the end. Chip unprotect can take several seconds and a user message should be
provided to show that the operation is progressing.
C.2
In-system technique
The in-system technique requires a high voltage level on the Reset/Blocks Temporary
Unprotect pin, RP. This can be achieved without violating the maximum ratings of the
components on the microprocessor bus, therefore this technique is suitable for use after the
Flash has been fitted to the system.
To protect a block follow the flowchart in Figure 17: In-system equipment block protect
flowchart. To unprotect the whole chip it is necessary to protect all of the blocks first, then all
the blocks can be unprotected at the same time. To unprotect the chip follow Figure 18: In-
The timing on these flowcharts is critical. Care should be taken to ensure that, where a
pause is specified, it is followed as closely as possible. Do not allow the microprocessor to
service interrupts that will upset the timing and do not abort the procedure before reaching
the end. Chip unprotect can take several seconds and a user message should be provided
to show that the operation is progressing.
相關PDF資料
PDF描述
M2CT-90A1-24ER PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT-THREADED
M2S56D30AKT-75 32M X 8 DDR DRAM, 0.75 ns, PDSO64
M2V56S30ATP-6 32M X 8 SYNCHRONOUS DRAM, 5.4 ns, PDSO54
M30-6000206 2 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT
M30-6000406 4 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT
相關代理商/技術參數
參數描述
M29W800FT70D11 制造商:Micron Technology Inc 功能描述:PARALLEL NOR - Gel-pak, waffle pack, wafer, diced wafer on film
M29W800FT70N3E 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TSOP
M29W800FT70N3F 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel
M29W800FT70N3F TR 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TSOP
M29W800FT70ZA3SE 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*